jetson tk1 case 3d models

WIP

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

This build adds a wider port for dual camera access

This remixed version has the following changes: - the holes made hollow so you don't have to make cut them yourselves (all antenna holes, cpu fan holes, and pinout holes) - the 4 rods on the top part have thicker fillet to prevent them from...

Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_thread_outer_diameter...

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Using the Following Options: - Nut step shape degrees = 45 - Nut height = 3 mm - Non thread diameter = 1 mm - Nut resolution = 0.5 - Thread...

Instructions Using the following settings: nut_height: Set to 6 mm Nut thread angle set at 45 degrees Non-threaded shaft diameter is 1 mm Nut resolution adjusted to 0.5 mm Thread length is now 55 mm Outer diameter of threaded nut section is...

# 3 Cases for your jetson nano rev. A02 #### I designed this so I could have a kali-like box on the go. #### Can manage small scale network security testing and penetration test. #### Designed to be slide in, no tool needed. Make sure you...

Carrying case for NVIDIA Jetson Nano and Powerbank Case for an NVIDIA Jetson Nano and a powerbank to make the Jetson portable for outdoor use. This case is for a Jetson Nano in a KKSB case and an Aukey powerbank as described in the BOM. I have...

This is a remix of the Jetson Nano Case by [ecoiras](https://www.thingiverse.com/thing:3518410) It is to get it to fit in with the [Raspberry Pi rack system](https://www.thingiverse.com/thing:3022136) and [DAP 2U rack...

... for the first remix, and this one shares only the mounting hole portion. ...Check it out: https://www.thingiverse.com/thing:1906831. It's designed to work with a modified case for a Jetson Nano, and I'll add a link once Thingiverse's site is back up.

You can download the display case files from the remix references You may use the tray system or print the directly linked part of the jetson case, depending if you want to be able to easily detach the computer from the display (the tray acts as a...

> NanoMesh Mini is a compact case design for the Jetson Nano Developer Kit. This case be used entirely tool-less, although it can be secured with four case screws. The carrier board is held in place with stand-off pins. To secure the case together...

This is a case I created for the NVIDIA Jetson Nano 4GB + Geekworm T208 UPS Module. By purchasing this 3D model you're authorized to print as many as you want for yourself, you are not allowed to print for your friend(s), print to sell, or...

Simple case for an NVIDIA Jetson Orin Nano Developer's Kit. All ports are exposed. There are four versions of the main case:Orin_nano_case_main has holes for accessing the terminal block of the recommended CAN bus (Waveshare SN65HVD230 CAN...

... and causes the hole not straight. Let me know if you have any good suggestions; I will consider all options. ps: Also working on a 120mm fan case since this 90mm case is already 110mm in width; why not just make it a little bigger, am I right?

Remixed the lid to better fit the 2GB version of the Jetson Nano which has a USB c connection instead of a round dc plug, as well as 3 USB's instead of 4 and no displayport. ...

These are the Case with I/O slot cover for the JetsonNano 1st/B01/2GB.It can be fitted with a fan.The SD card is not allowed to fall into the gap. JetsonNano Case for JetsonNano 1stJetsonNano_Case_Case_Top_A is Top Case with Top I/O...

Xavier NX Case remix (https://www.thingiverse.com/thing:4523772) with open bottom to access bottom header

Human: TK1-007 Chase Run Animation Data For characters with extremely short limbs, and four fingers on each hand. ... • Frame Rates: 24 fps or 30 fps • Number of frames: 239 or 297 • Formats: .bvh or .bip • Version (Review): 3.51a, dated October 31,...

TK1-006 Huffy Walk Animation Data For tiny characters with super short arms and legs, each hand sporting four dexterous fingers. ...Frame Rates: 24 fps // 30 fps Number of Frames: 241 // 301 Formats: .bvh // .bip Version Review: 3.51a (October 30, 2015)

Animated Character - Toon Kid 1 - Leisurely Saunter TK1-004 Animation Information For small characters with short limbs and four fingers on each hand. ... • Frame Rates: 24 frames per second, 30 frames per second • Number of Frames: 241, 302 • Formats:...

TK1-008 Fast Run Animation Data For tiny characters with short limbs and four fingers on each hand. ... • Frame Rates: 24 fps // 30 fps • Number of Frames: 241 // 301 • Formats Available: .bvh, .bip • Version Review: 3.51a (Updated November 2, 2015)

This is a simple base for a [TK1 Soviet telegraph key](https://www.radiomuseum.org/r/military_telegraph_key_tk1.html). Although it doesn't really provide enough weight for efficient use of the key, it is compact and portable. The base is attached...

This is a simple base for a TK1 Soviet telegraph key. Although it doesn't really provide enough weight for efficient use of the key, it is compact and portable. The base is attached with four M3×16mm nut/screw pairs. Two versions are provided. One...

for 3d printer

Achieve superior print quality at optimal resolution and ensure zero warpage for exceptional results.

I modified the button to extend 5 mm below the nano module for a specific reason. ...Additionally, I haven't printed the design yet, but I'm confident that it will work perfectly since only the button was relocated and none of the interface areas where...

It was hard to print with the hexagon pattern on the side panel of bottom part so, changed that part for easy print.

Designed by Inventor Pro 2024, have fun