jetson nx case 3d models

It might be worth printing in ABS in this case, or using a cutoff of 1mm sheet metal glued to the bottom of the duct to prevent warping.\nAs of uploading this item, I have printed 3.5 hours without any change in the shape of the duct.\nHow I Designed...

I also added a mount for a 40mm fan to cool the motor just in case as I was printing this in PLA. None existed that I could see so I made this one. It should mount easily on most any extrusion but, if not I'm sure you could get creative for a...

There are various lights from Hella in this series with only minor (if at all) differences and package contentstwo sheet metal screws 3.5x9.5 mm (in the case your light comes without screws)some cables and connectors to make up the inards of the...

nuts) to check fittings * I used simple PLA * Print in fine resolution (0.1mm) * Print with slight support (only connections from base) * Use Skirt (not brim) * Fit might be very tight (and adapted to the material I had at home) – so check your...

In our case, we chose to recreate the no longer available "Behind the Box Solutions" because it was the cleanest design. Buying pre-made would have been preferred, but that wasn't an option. My version is surely different, but it works and installs...

The controller case takes up most of the right side of the printer, which is why I designed this project in the first place. My goal was to be able to re-use as much of the controller box parts as possible. When I designed the Ultimate Tronxy...

To be honest, I estimate that for many use cases stage one is already "good enough" and it has a far better price to performance ratio than this stage two. So you might start out using stage one and then find out how much dust still ends up in your...

This is a very sturdy wall mount for the LEGO Space Shuttle Discovery - a mighty complex object to put together there - if you don't have a big display case then you wonder where to leave it?I wanted a wall mount that was small and inconspicuous, but...

-With the open motor base housing, you can still turn it by hands, wich is not always the case with direct extruders and sometimes helpfull. -it can use flexible filament (depending on the extruder drive you choose). -If you like me having problems...

... <p><strong>Infill:</strong> 20%</p> <p><strong>Notes:</strong></p> <p>Supports are only required for the bottom part. This is for the USB hole. The top case does not require any supports and can be printed face down and should turn out great.

It might be overkill but it's definitely sturdy. For the rods and bushings you will need two each per lifter unit: Misumi Straight Precision Linear Shaft - PSFJ12 THK Long Linear Bushing - LM12LUU For my printer I used PSFJ12-455 Rods. To attach the...

the axel and bearing's inner roller must form a fixed subassemby, and the outer roller of the bearing is simply held in place by the holder's geometry (has it has a rim on the outside, so once assembled the bearings physically can't come out) I'd...

Which one you print depends on which side of your drag chain links open up -- if they open up to the outside, pick `Open Max`, but if it opens on the inside, pick `Open Min` (Min/Max in this case referring to where on the X axis the drag chain opens...

For the clear parts, I recommend printing at 100% infill, and in the case of the lamps, printing with a brim instead of a skirt. The two lamps with the dome on top of the housing will also need support. After printing make sure to paint the...

This is a rear mounted cooling duct for stock 40mm fan of Wanhao Duplicator i3 v2.1 (to be screwed to one of the printing head's lower bearing plastic casing M4 holes). It is designed to be attached to the printing head with a 20mm M4 screw with...

I had them 3D printed individually in case of any errors that I did not notice while CADing. Once printed, I put the device together and tested it out while eating Japanese food with my friend! In order to use it, all you have to do is tie the strap...

You will need to print 2 grid.STL so that you can sandwich your filtering material in between them Combined cap and grid: I uploaded gridCap.stl which combines the normal size grid and cap into one part, just in case you want to cut down on the parts...

This should not be necessary normally, but in case of any issues... On the bottom of the block I added a side gantry that may help to cool the filament and drive gear better, and provides an escape route for shavings when clearing the drive without...

In that case I would stick with the Prusa buffer.I have a solution to add friction in the rare cases on the slot buffer where loops get pushed back to the spool, so that is not a problem with this design. The hanging endpoints in my setup allows you...

With the screws removed, you should be able to pull off the top of the servo case. This will reveal the gear train. </li> <img alt="Servo" height="600"...

#### TFT Firmware Rollback In case you have issues with this custom firmware or you don't like it, you can rollback to the firmware previously installed in your printer. In order to rollback: 1. Download the stock Artillery TFT firmware (from...

It was in one piece for just long enough to print out a decent Benchy before the little voices in my head whisperingscrew with it! got too loud to ignore. So I thought I'd document some of that here, in case anyone else might find it useful! Things I...

And since it was easy to change the density on the model and the density in the print settings I made models and project files for each of the commonly used densities in case anyone wants one of those. These models require about 1/4 the material and...

The dryer shows an acceptable overshoot after letting the PID controller complete auto-calibration.In case of a small amount of temperature overshooting, the lower drying temperature of the filament can be used to overcome it. For example, the...

2 Place the balls (D3mm) on the raceway of the rear half-case (Spinner-BodyP402.STL). Slide the 32-tooth bevel gear (Wheel_con_32T.STL) until it rests on the balls. Its rotation must be free and fluid (without hard point). If necessary, grind the...

Custom Parts !1x P-100-MINI-z-bottom-mks-robin-e3d-v1.1-case-Z-mod.stl1x P-101-MINI-z-bottom-cover.stl1x P-103-MINI-heatsink-fan-holder.stl1x P-104-MINI-heatsink-clamp.stl1x P-105-MINI-frontfan-holder.stl1x P-106-MINI-join-plate-with-z-carriage.stl1x...

Worst case if you destroy the threads you can tap for M4 or just put a nut on the back. M6 screws should be sufficient if you thread the plastic. M8 or M10 will give you enough extra length to use a nut on the back.</p> <p><strong>Install hopper and...

Then you need to spin it in the opposite direction.I uploaded many sizes (inner diameter in mm from 12.3mm for kids to 24mm for big fingers, please use the conversion table below in case you are used to your local ring sizes and use the closest value...

I uploaded many sizes (inner diameter in mm from 12mm for kids to 24mm for big fingers, please use the conversion table below in case you are used to your local ring sizes and use the closest value in millimeter). The STL filenames have the inner...

&nbsp;In that case:I first assembled all of the squares on the frames, dry-fit.&nbsp;Then I popped-out each of the Colour02 squares, one at a time, without moving the rest of them.&nbsp;I put a small stripe of superglue on each visible part of the...