jetson nano case 3d print

Case for RadiationD-v1.1 (CAJOE) Geiger Counter GC-1602-NANO.Plexiglass flesh with the wallsPower sockets and on/off switch accessible.No hole for the audio jack.

A remix of Jonvanderveen's Nano 7g case, with a belt clip added. ... Reduced width by .3mm to give a better grip on the iPod.

... the gcode or place it in the slicer at layer change) and insert the magnets during print. For the Logo you can print the bottom case with the logo embedded or print the logo in accent color and the case with the logo left out ontop of it. ...

I finally found the PCDuino3 Nano and Nano Lite cases to be elusive items (as well as support!). I couldn't locate one that fit my needs of also housing a 2.5" SATA hard drive, which was the reason I purchased it. So I decided to create one myself!

Karabas Nano: https://github.com/andykarpov/karabas-nano Based on rev.C. Later revisions differ in some details and may be incompatible with this design. Photos are actually from the first iteration of the process. It was intended to be changed...

Building the Model Colors (there is only one printed piece) Black: eyebrow, eye, mouth, ring top, ring bottom, stripes, buckle Beige or Flesh: head, hand left, hand right White: shirt, shoes, arm left, arm right, eye white Orange: hair top, hair...

I just found a fantastic source of inspiration - the original iPod nano case by someone I couldn't recall. I made some clever modifications by nudging the tabs slightly outwards, and added my good friend RD's adorable cutie mark for good measure! ...To...

New Ledger version - Nano S Plus - doesn't come with the insert, so I made one that fits this great case.Settings for best results:TPU1 perimeter10% gyroid infill3 bottom layers0 top layers3 top layers for the inside part (Hilbert curve for nice...

Originally designed for a basic stopwatch application, this mounting case accommodates a standard button with a 16mm thread diameter as well as a stand for an Arduino Nano. To secure the display in place, M3 screws were utilized. ...The faceplate...

To print this case, follow the instructions provided - print the bottom and top parts with snaps that allow some play without breaking. Let us know if any alterations are needed. Secure the quadcopter in place by using an elastic band across the 4...

If you have the proper filament colors, no painting is needed. The assembled model is 235mm tall and is in proportion to my George Jetson model. Enjoy! Print instructionsPrint Instructions Supports: No Resolution: .2mm Infill: 10% Notes:** Refer to...

If you have the proper filament colors, no painting is needed. The assembled model is 200mm tall and is in proportion to my other Jetsons models. Enjoy!...

Once I got everything working (still working on limit signals), I decided I needed a case for my setup so back to 3D printing. I'm a programmer by trade so I prefer designing with code when possible. I love OpenSCAD but the syntax is overly complex,...

To add these features to the Nano Pi2, simply print the three pieces proposed here which are intended to replace the parts of the complete kit found at https://www.thingiverse.com/thing:2514014. When mounting, first install the LCD screen and then...

JetBug - Modified Jetson Nano Jetracer Base for: Tamiya M-05 1/10 R/C car Tamiya TT-02 1/10 R/C car Any short frame 1/10 R/C car Donkey Car Raspberry Pi Team JetBug, we are students from ESF Island School, Hong Kong. Our car is based on open source...

... for a WH148 potentiometer. Optionally, you can use a fastener to secure wires or an LED strip directly to the case. The Nano can also be screwed directly into the case. ... You can use M1.2 4mm screws or similar to secure the fastener and LED.

This is a case that fits an Arduino Nano and has room for a power switch, along with a hole to run wires out of the case. This does not fit a Nano that has the header pins attached. Let me know if you have any questions! ... Also check out my second...

......You can find the hardware setup and the firmware for Girs at https://github.com/bengtmartensson/AGirs This case is meant to hold the Nano, a 5mm infrared LED and a TSMP-58000 IR receiver. Please consult the above mentioned documentation for details.

I crafted this custom case to snugly fit an Arduino Nano inside the terminal adapter from China, found at...

This is the 3D Printed parts of my designed 2" Nano Toothpick. Frame: https://cults3d.com/en/3d-model/various/apus-2-nano-toothpick-frame You can see the complete setup and hardware information in: https://rotorbuilds.com/build/22671 If you liked,...

Print Settings Printer: FlashForge Creator X Rafts: Not needed Supports: None required Resolution: 0.2mm Infill: 10% Notes: Check below for helpful printing and assembly tips. Building the Model Colors (there are no multiple printed pieces) Black:...

The exhaust part should be printed with no infill Refer to the notes below for a few helpful printing and assembly instructions. ........................................................................................................... ...

**Print Instructions:**Supports: NoResolution: .2mmInfill: 10% Notes:** One part has built-in supports.The exhaust part should be printed with no infillRefer to the notes below for a few helpful printing and assembly instructions. **Building the...

The exhaust part should be printed with no infill Refer to the notes below for a few helpful printing and assembly instructions. ........................................................................................................... Building...

This is my design for a Ledger Nano S Case to store my WGMInterfaces mint! This is a Fan Art/Project. It is not meant to be commercialized. ... More information on the WGMInterfaces project go to their Twitter @WGMInterfaces.

Remix of a simple case to house RC522, Arduino Nano, and SSD1306 128x64 OLED.This is not a well made RFID unit and read range is very low. ... Reccomend a different project.

Case for RadiationD-v1.1 (CAJOE) Geiger Counter GC-1602-NANO.Plexiglass flesh with the wallsPower sockets and on/off switch accessible.No hole for the audio jack.

Here is version 3 of the DE10 Nano Stack case. The Cube! With space for a 90mm fan, this rugged cube-shaped block of printed plastic armour should keep your DE10 cool and well protected. Like the bunker version before it, it is a fit and forget...

Print Settings: When printing this case using PLA filament, it's recommended to use a layer height of 0.24 and apply -0.12 inches of XY Size Compensation in Slic3r to account for the small PCB groove and prevent overflow issues during the printing...

The print pictured above has a 0.28 layer height; the only thing that's a must is printing with Supports / Touching build plate, other than that no particular settings. The Arduino slot might be a little bit bigger than the PCB itself (my clone was...