jet stream model

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

 On my ESC I have to start with the minimum setting (effectively the throttle channel on an RC model), which I believe is a great safety feature.  BTW you can also program your ESC using the knob as if it was a throttle control, if your...

This is an OpenSCAD module library for propellers and spinners.This design models elliptical propeller blades that transition smoothly through three different NACA airfoils, starting with (by default) NACA 8430 at the hub radius, transitioning to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

Make sure to follow me to get a notification when it's uploaded!*** ------------------------------------------------------------------------------------------------------------- ###READ BEFORE PRINTING!### * First of all, this is a non-commercial...

I checked with Meshmixer and the model is fine. Tried re-exporting from F360 to a new file and experienced the same issue. I opened a bug report, but Ultimaker closed it as not being able to duplicate.</strong></p> <hr/> <p>The case is designed to be...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

A big thanks also to Eric Clinedinst who helped me to find the first issue. This is the BOM list for the internal part: 1x 5x10x4 (MR105z) Bearing for indirect filament sensor 1x round neodymium 8x3...

The model was made to accomodate minimaly these dimensions : X=50mm, Y=110mm, Z=165mm&nbsp;AssemblyGeneral tip : don't over-thighten any screw !&nbsp;Step 1Print the parts needed (the casing, the door and the caps if you want them).&nbsp;Step...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

Basic overview:This is a drop in replacement barrel for the Dart Zone Solo Pro that is designed to allow it to fire mega darts, but I designed the model in a way that it can not only also still fire half darts, but fire rival ammo too! It shoots Mega...

UPDATE: The model has been printed & test fit. Like a freakin' glove. #caliperlove Inserting the letters requires a bit of finesse & just enough brute force not to break the R and X apart- just be patient & make sure to clear any wisps/stringing in...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

Http://www.Thingiverse.Com/Apps/Customizer/Run?Thing_id=507810 Instructions Using the Following Options: Custom_phone_width = 100 custom_bottom_fillet_resolution = 8 printer_tolerance = 0.4 stencil_vertical_position = 50 custom_case_pattern_thickness...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

&nbsp;- Click on the "Download" button and you will find the download file in small print coloured light grey below the Model &nbsp;files.&nbsp;Using Onshape is easy - open the attached link, and double-click on the #BOTTLE_DIAMETER parameter to...

* Once assembled my new FelFil extruder (https://cults3d.com/en/3d-model/tool/felfil-evo-extruder-case) I began to design a cheap and affordable spool winder; I had to design a cooler for extruded filament and a digital sensor for filament diameter.

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

I think it fits 5L)A water tap (Only if you don't want to print the models “water tap” and “valve”! If you want to buy one, make sure it is long enough to get over the bumper of your car. For example: <a...

Bear Exxa 1.0 is available here: https://www.thingiverse.com/thing:4362586 IMPORTANT: The Bear X axis will currently limit you to what alternative extruder/tool options you can mount without creating an adapter plate as it is different than previous...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

I sliced it with Cura 4.4 so you can use per model settings to print the whole thing at once. I printed it at .15mm layer height. Here's a video of the toy with some details. The video has a lot of assembly photos at the...

You may also be able to gently fit the parts into each other and twist to get a sense for how smoothly the connectors fit. Place in a sealable/zip-top plastic bag. Print and fill out a form to help the hospital and make certain that you, as a maker...

I'm no design expert, and 3D modelling makes my brain hurt. However, with a lot of perseverance, a set of calipers, hundreds of edits and redesigns, dozens of test prints, I have made a replacement ring battery.</p><p>You will need the...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

I do not own a BL Touch so this design was based on 3D models so definitely WIP. I have increased the thickness of the Duct mount to the base unit to make it even more robust on the LH duct. You may now need to use M3 x 10 mm to fix to the base unit....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

... marked a new beginning in the brand's legendary history while setting a fresh course for the American brand. Visit our website to see more of this model or any other additional services you might need. ... Tires texture not included in this set.