jennyprinter 3d models

Print Settings Printer: JennyPrinter Rafts: No Supports: No Resolution: 0,25mm Infill: 20% Notes: Print however you like. I've printed with 2 and 3 perimeters. The bot works fine. Also 0,2 and 0,25. Same result pretty much. Post-Printing ...

Say goodbye to sloppy curling edges and unsightly overhangs once and for all! Enjoy the sleek 80-degree overhang without any pesky supports in sight. ...Try the standard version of this fantastic fan duct here: http://www.thingiverse.com/thing:1492821

Here's a rewritten version of the original text: JennyPrint Ultimaker 2 Hot Bed Cable Chain Bottom End Fixing Device for China Market

Jenny's Dual Extrusion Fan Duct prints flawlessly on a 30x30x10 inch fan. This setup pairs the Jenny machine with a ten-axis external axis and an E3D Chimera 2 dual extruder cooling fan mount. ... After the upgrade, the single nozzle printing area...

Building a DIY Dual-Extrusion machine using the Chimera+ dual nozzle hotend, and been trying to find just the right layer cooling solution. Liked this one the most, but the fixing seem to be inverted and my cabling got in the way a bit, so just...

Print Settings Printer: JennyPrinter z360 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 50 Notes: Printing with about 80% infill was a good choice for me because I wanted the item to be strong, and any infill setting between 20-100...

This fits into many other projects and it actually fits perfectly into at least the open-sided JennyPrinters' front lcd space. ... There are two versions: one is a standard design and another is specifically designed to make room for an alternative...

Human: Successfully reverse-engineered a stepper spacer compatible with the JennyPrinter (Ultimaker clone).\r\nPrintable in PETG, ABS or other high-temperature materials to accommodate heat buildup from the stepper.\r\nDesigned for both X and Y axis...

BOM: You'll Need the Following Parts: 4x M3 10mm Screws 4x M3 Nuts 4x M3 Plastic Spacers (Optional) Print Settings: Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.3 Infill: 10% Notes: I Printed Mine Using a 0.4mm Nozzle, with 2...

Print Settings Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.25mm Infill: 100% Notes: The piece is 1.25mm high; use a layer height that divides evenly into it for optimal results. Initial printing was done solid, but alternative methods...

BOM: * 4 PCS 20mm 3mm screws * 4 PCS M3 nuts * Fixing to 6mm sides: + 2 PCS 12mm 3mm screws + 2 PCS M3 nuts Print Settings: Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Notes: * 1.2mm between each letter, which means a...

To print the motor clamp, use the following settings: Printer - JennyPrinter; Rafts - No; Supports - No; Resolution - 0.25mm; Infill - 25%. Note that using a 0.4mm nozzle with three perimeters is recommended for printing this part. Avoid using...

Print Settings Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.25 Infill: 20 Notes: I printed it at 0.25 layer height using 0.4mm nozzle and 3 perimeters... I guess 2 perimeters would be fine, and you can use higher layers as well. ...Might...

Print Settings Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.23 Infill: 70% Notes: You should use 0.23 layer height for optimal accuracy as the "base" for the nut. I used a 0.4mm nozzle. Three perimeters were printed. I produced prints...

Printer Settings Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Notes: No support is needed; print as they are oriented. I used a 0.4mm nozzle and had 2 perimeters/borders, along with 25% infill. ... Design Process I...

... hardware to match your printer. Print Settings: Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Notes: You may use coarser settings if desired. ... Post-Printing Instructions: Insert the M3 nuts into the cut-outs.

Print Settings Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.25mm Infill: 55% Notes: Use 3 perimeters. Custom Section Foot Drilling Guide Two simple drilling guides were added to ensure accurate hole placement for the feet. The guide...

There is a standard STL download available here on Thingiverse as usual: Print Settings: Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.25mm Infill: 70% Notes: I employed 3 perimeters using a 0.4mm nozzle. It is recommended to use a...

Print Settings Printer: JennyPrinter Rafts: No Supports: No Resolution: 0.2 Infill: 20% Notes: I've printed using a 0.4mm nozzle. I have also printed with 0.25mm layers with fine results. 2-3 Perimeters The CaseBrackets and MountingBracket should be...