jdm to us license plate adapter 3d models

This adapter attaches directly to the original plate mounting locations found on a JDM vehicle, allowing for the installation of a North American plate. The NA plate is positioned downward by 6mm due to height differences, enabling the use of lower...

This is a single piece adapter to allow you to mount a North American license plate (7in center to center mounting holes) to a car with JDM mounting points (210mm). ... In order to use this solution, you will need two countersunk M6 bolts to connect to...

Remade this (recreated from scratch using original as reference in Fusion 360) with some minor scale adjustments. ...Swapped out the authentic license plate screw for a standard M6 screw and modified the nut groove to fit snugly around an M6 nut.

These adapters will enable you to securely attach an unaltered US plate to your EU plate bracket using only standard hardware. Available for printing with ABS or HIPS - PLA may be too prone to cracking due to the undersized mounting holes, which can...

This adapter lets you put a Canadian or NA license plate on your JDM vehicle. It was designed for my Subaru Legacy B4/GTB. The bigger hole is for an M6 bolt, while the smaller one holds the license plate in place - you'll need a washer for it. It...

A converter is needed, so the US License plate can attached to the car with more than one screw. I looked online...and people are charging $20-50 for an adapter. What?!? GTFO! So I decided to design my own...it wasn't hard, just some trial and...

The US-style plates won't fit directly because the euro holes are 120mm apart and the US holes are 146mm wide. To make it work, you'll need some M6 nuts and bolts made of stainless steel with Nylock nuts for extra security. ... I built the prototype...

The US style plates don't fit directly, the euro holes are 120mm apart (4.75in) and the US holes are 146mm (5.75in). You'll need some M6 nuts and bolts, preferably stainless steel, with Nylock nuts for sercurity. ... I made the prototype in PLA, but...

The license plate holder on my 2012 GMC Sierra was recessed into the bumper which made it hard to mount my fire department tag behind the plate, so I made this spacer to push the license plate forward and be able to mount the tag properly. ... The...

Headlight adapter to fit a specific headlight. Light filaments sit at same depth as original and reflection is perfect. Need to make another solution for locking them in place as the bar doesn't fit anymore. ...Link is for the light itself, ( Fahren...

Experimental adapter to fit EU switches on US electrical boxes. ... Designed to work with the new Shelly switches.

... I've included a remix from: https://www.thingiverse.com/thing:2653593 Here are the dimensions for your plate, captured in an image. Next up, I'll be adding more Australian states to the mix - just need to do some digging first, so bear with me!

... FOR MODIFICATIONS. ATTACH THE LICENSE PLATE TO THE HOLDER USING BOLTS/SCREWS WITH A WASHER BETWEEN THEM. THIS PREVENTS UNDUE STRESS ON THE HOLDER AND PROTECTS YOUR VEHICLE'S FINISH. ... IF YOU ENJOY THIS DESIGN, CONSIDER TIPPING ME A COFFEE!

Attach the license plate to the holder using bolts/screws and placing a washer between the license plate and the holder. This washer is important to avoid placing undo stress on the holder and to avoid having the bolts come into contact with your...

Digital File, to 3D print, F@!k Joe Biden political license plate frame. Show others your feelings on the elected president and his polices. You need a larger printer to make this one part and not print in sections. ...Physical print can be found in the...

I created this adapter and printed it in PETG, which allowed me to successfully mount my plate to the car. The 2 screws mounting the adapter to the bumper should be M6s. ... The screws mounting the plate to the adapter should be M5s going right into...

This is a rear license plate camera adapter designed to center an attaching camera directly in the middle of a standard license plate. To ensure this adapter holds up to harsh weather conditions, I highly recommend using ABS plastic for its...

Quick and simple license plate adapter to go from JDM to USA plate spacing. Printed for M5 cap screws to the truck, with threaded M5x0.8mm holes for the US license plate. ... Print however you want, I used a tap to clean up the threaded M5 holes.

... same holes that the OEM standing plate mount uses. ...Though you will have to drill the holes in the mount to actually hold the plate to the mount. I might update later and add the holes. ...Ive had it mounted for 2 weeks now with no problems at all.

show others your thoughts on President Joe Biden with this vanity license plate frame.

American companies are adapting to European standards.

My license plate cover broke and didn't want to spend $30 on amazon for a simple piece of plastic. Can be customized or text added to it, or printed with multi coloured filaments. no supports, .6mm nozzle about 2 hours @ 100%fill Printed in...

A set of JDM-stylized license plates, made in the dimensions of original japanese vehicle registration plates (330mm wide and 165mm tall) without any holes or other modifications (left our to best fit your use-case). I have misplaced my original...

Click 'Open in Customizer' to craft your own motorcycle license plate holder with personalized text. It fits American motorcycle plates perfectly - results may vary, a clever pun intended. Print Settings No supports or fancy features are necessary...

I wanted a customizable license plate frame that could easily print on my regular sized printer (Print area of 250mmx220mm) but couldn't find one. This is a blank frame that can be easily assembled (I used epoxy on the few I've made as it fills the...

I bought a 2022 Beta XTrainer and did not want to pay $15 for a plastic license plate adapter for a U.S. motorcycle plate so designed my own. ...It is a perfect fit and is likely it will fit other Beta motorcycles, or perhaps other European bikes.

This adapter is designed to connect a standard-sized trailer plate to the regular license plate mount area on your vehicle. The reason behind this design was due to the fact that my county only issued smaller plates for trailers, whereas the original...

Wanted to create a simple low profile design to replace a large heavy steel adaptor plate that was poorly made that came with my euro bumpers. These articulate and can be adjusted up or down depending on preference. I used stainless hardware to...

Mitsubishi galant jdm front license plate cover.

his is a license plate adapter to fit a North American license plate to an Italian car. It worked for my 1972 Autobianchi Giardiniera, but I based it on information I found in general for Italian license plates as well. I've used it with a standard...