jarvis desk drawer 3d models
72322 3d models found related to jarvis desk drawer.thingiverse
Simple underdesk drawer to mount on the bottom of a Jarvis standing desk. ...Attaches with double-sided tape.
thingiverse
Remixed design from https://www.thingiverse.com/thing:1031950 to fit a 27mm thick desk like my Fully Jarvis desktop.
thingiverse
A headphone hanger clip designed for the Fully Jarvis (https://www.fully.com/standing-desks/jarvis.html) Bamboo Standing Desk. There are two clips: * A standard headphone clip. Nothing special, just fits the desk well. Could also be used for...
cgtrader
Fully Jarvis Electric height adjustable table. ... Units: mm Textures: 5 pieces (1800 x 386 - 6800 x 6800)
prusaprinters
This is a cable management tray cover meant for an Fully Jarvis standing desk. It is mounted on the frame ends as Fully calls them. It has been heavily inspired by the <a...
thingiverse
# Fully Jarvis Headphone Hook This under-desk headphone hook is custom made for the Fully Jarvis standing desk. It features a curved hook for headphones as well as a smaller hook on the other side for cables. The design slides on to the standing...
prusaprinters
This is a remix of NVNTstudio's Modular Desk Organizer, designed to slip over the edge of a Javris desk.I had trouble getting command strips to adhere to the desk and hold pens up, so I modified the original version to slip directly over the edge of...
thingiverse
Headphone hook for the Fully Jarvis Laminate desk top and Jabra Evolve 40 headset.
thingiverse
These spiked feet improve the stability of the [Fully Jarvis Standing Desk](https://www.fully.com/standing-desks/jarvis.html) by redirecting more of the weight of the desk past the carpet and into the sub floor.
thingiverse
This is a remix, as the original was too small for my Fully Jarvis Bamboo desk. The original appears to be for a 20mm desk, this remix is for a (/my) 23mm desk. It also holds Jabra's controller. Because my 23mm is a tight fit, I have also included...
thingiverse
a desk drawer i hope you like it and the desk drawer part2 i put upright for the It may take a while because of the supports but you can change it
grabcad
This is a simple add on Desk Drawer for under a work bench, table etc. ...I am also uploading a smaller one.
thingiverse
### 4 parts for this drawer: - drawer.stl - Drawer itself to put your goods into - drawer-frame-left.stl - Left side frame - drawer-frame-right.stl - Right side frame, a mirrored object of left side frame - drawer-front-panel.stl - Front panel to...
thingiverse
This small desk drawer is easy to install and fits seamlessly into any workspace. Its compact size makes it ideal for smaller desks or workstations, while still providing ample storage space for your essentials. ...
prusaprinters
The size of drawer is 150mm x 180mm x 42mm. Print instructions4 parts for this drawer drawer.stl Drawer itself to put your goods into drawer-frame-left.stl Left side frame drawer-frame-right.stl Right side frame, a mirrored object of left side...
thingiverse
This is a straightforward desk drawer perfect for plank-style desktops. The drawer consists of four printed sections that are carefully glued together to form a single unit. Each individual drawer section measures 160mm square by 50mm tall. To...
grabcad
Office Furniture - Showcasing a Drawer DeskReceive Kudos for This Design Submitted by you, it's a Drawer Desk in the office furniture category that has caught your attention. ...Appreciation in the form of likes is encouraged to share your positive...
thingiverse
Designed using TinkerCad I love speeding prints up as much as possible and not using supports I have seen many very good under desk drawers on Thingiverse, but I am not patient! Some take as long as 2 days to print! The shortest I think was still 18...
thingiverse
Size Size overall 18.0 x 20.5 x 6.0 cm (WxLxH) Desk outer 17.0 x 20.0 x 5.0 cm (WxLxH) Desk iner 16.5 x 19.5 x 4.8 cm (WxLxH) The holder is printed in PLA and the drawer is printet with ASA. I'll recommend printing both parts in PLA. Drawer facing...
prusaprinters
Desk drawer to be mounted from underneath the desk.There are three versions with varying lengths availableLxWxH (inside):240 (219) x 200 (174) x 50 (45) mm220 (199) x 200 (174) x 50 (45) mm200 (179) x 200 (174) x 50 (45) mmEach version have their own...
thingiverse
I designed this DIY project to make assembling a simple drawer a breeze. ...I haven't yet had the chance to print it out and give it a try, but I'm eagerly awaiting the arrival of my new printer so I can put it to the test.
thingiverse
View the 3D version of yourself in the 'Thingiviewer' or take it home as an .stl file; download a complimentary open-source .stl viewer from various online sources by searching "free stl viewer" to see your 3D self on your computer.
thingiverse
Customized Version of https://www.thingiverse.com/thing:1011232 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1011232 Instructions Using the following settings: model_name = Zeus carabiner_option...
thingiverse
I designed this with a friend who has a large desk drawer- it prints in 12 pieces that have to be glued together. ... The dimensions are (roughly) 32cm wide 48cm long 4cm tall
cults3d
I designed this with a friend who has a large desk drawer- it prints in 12 pieces that have to be glued together. ... The dimensions are (roughly) 32cm wide 48cm long 4cm tall
prusaprinters
I designed this with a friend who has a large desk drawer- it prints in 12 pieces that have to be glued together. The dimensions are (roughly) 32cm wide 48cm long 4cm tall Category: 3D Printing
thingiverse
I just added a clip to keep the controller of my Plantronics Blackwire headset to the original design.