jager ads 3d models

- belknap-ascension-double-torpedoes.stl | Alternate Ascension torpedo module with added rear tubes. - kteremny-command-module.stl | Front command module. -...

The printed parts are actually the same, it's just the front and rear panels that are different but I prefer to keep them apart for different reasons.For most user cases, one or two dryers should be sufficient but it depends on what type of filament...

I have also added short pegs to hold the chess pieces in-place, when the game is traveling. [NOTE: After early feedback on the original post, I have modified the board pieces to be thicker, with chamfered tabs, tapered posts, and 0.1mm spacing...

I've added a 3D printable 18650 battery holder specific to this build. There's no reason why you couldn't buy one or use the base frame as-is if you're happy soldering flying leads to your batteries but this design should lock in to the frame...

It's a fun, satisfying effect for a little pencil organizer. Accessory Bin Adding a bin to this drawer is problematic because it sits against the bottom of a desk or shelf. You can't easily look inside a deep bin or lift something out. This bin is...

the one shown in the video holds 4ml which is insane and unnecessary so I made it smaller, and added a double seal O-ring in the slot for safety :) How to make:Lubrication is NOT OPTIONAL! (unless you enjoy leaks/inky hands :P).For Silicone...

The earlier posted configurable floor stand - customized with a “don't touch” message and your name (1250 names are included).Print instructionsPrint without supports, change the filament color at 4.8mm while printing to get a well readable...

The mounting holes for the extruders differ so much I could not make a universal carriage without it being bulkier than I wanted for this lightweight system.Update November 24, 2021I've added a back to stock firmware gcode you can print if you want...

Just be aware of the friction added by additional PTFE tubes on the filament's path to the printer. When you unload the filament from the printer, roll the spool back, so the filament just stays out a bit from the bottom mount hole. The next time...

The ELRS.lua file will be added to the tango card in the folder :/SCRIPTS, and inside this, in the folder /TOOLS. When we keep pressed the menu button of the transmitter, it should appear automatically under the Script that we use to configure the...

When I do upgrade my machine (or when I get bored) I'll draw up a nicer optimized mount for the 525...unless someone beats me to it :D Introduction to this version: https://www.youtube.com/watch?v=nYEQ5p\_Yi5k Cutting a full sheet with this cutter: ...

In addition, I added relevant hashtags to make it more searchable on social media. If you would like a different spin or have any other requests, please let me know!</s> щть</s> щть</s> щть</s> щть</s> щть</s> щть</s> щть</s> щть</s> щть</s> щть</s>...

You have control over the speed, depth and rhythm of penetration The Sex Chair Sliding Rocker Chair is powered by the movements of your body You can create quick, deep thrusts or slow, deliberate ones In this model, an adjustable platform for...

PRINTINGAlmost all the parts are already oriented on a flat surface, and should be printed as-is without rotating or adding supports. I printed at a layer height of 0.1mm for just about everything except for parts like the alligner or the large...

... enjoyed working on this game for the competition and getting to finally play a working version of it with my family. I hope you enjoy it!&nbsp;Version 1.1 update: Added the “tunnel” part along with printing and assembly instructions for it.&nbsp;

The copper free aluminum alloy body is powder coated for added durability and an attractive aesthetic appearance. A special heat dissipating design in conjunction with LED technology helps this fixture to achieve an excellent 60,000 hour rated...

Except for the figures and token racks which are one-color, all pieces are printed as two-color by changing the color layer by layer (for example, using the M600 command, or manually changing the filament).&nbsp;MANUAL:Game content :- 1x Centre...

The mounting holes for the extruders differ so much I could not make a universal carriage without it being bulkier than I wanted for this lightweight system.Update November 24, 2021I've added a back to stock firmware gcode you can print if you want...

This bike needs a 5mm wide belt and for that I designed and added to the files a "belt divider" to get out two 5mm belts from one 10mm belt. Hurraaah!!! Included gears for this belt system are 13T for the main axle and 30T for the wheel. To use them...

Each temperature reading was given at least 20 minutes to reach the steady-state before recording.The selected 300W PTC heater will not heat the internal temperature above 85 degrees Celsius even if the temperature is set to 90 degrees Celsius.When...

You can use pliers, clamps or just flip it upside down and press it against a hard surface.The result should look something like this:It is not required to use all the holes, I just added some extras in case some come out too undersized. Also it is...

- Workaround 4: Copy the font to a path and in OpenSCAD write "use " Additional hints for adding symbols using OpenSCAD: - For symbols you need to say where the symbol should be: - add_a_special_character="left"; - Then there are two types of...

The copper free aluminum alloy body is powder coated for added durability and an attractive aesthetic appearance. A special heat dissipating design in conjunction with LED technology helps this fixture to achieve an excellent 60,000 hour rated...

* It would be a good idea to bench test the setup prior to final assembly of the back covers, to see if adding additional power points to the middle or end would help. I had to go back and add power to the middle and end, after I thought it was...

To take out that slack, I hit on the idea of adding label strips around the top edges of the frame, with a thin edge that fills the gap. ...I made those label strips match the profile of the board borders by "subtracting" the board from the...

[You can also find this project at my Google Drive location: ] This is the 23rd expansion parts kit meant to complement my original [Star Trek Constitution Class Parts Kit](https://cults3d.com/en/3d-model/game/star-trek-constitution-class-parts-kit),...

The copper free aluminum alloy body is powder coated for added durability and an attractive aesthetic appearance. A special heat dissipating design in conjunction with LED technology helps this fixture to achieve an excellent 60,000 hour rated...

An added twist is that Printables.com does not like the JSON file either, so I renamed it to mini-tray_json.txt. After downloading, you will have to translate it back.</p><p>The JSON file contains settings for various packages (conforming to the...

**Rods:** - 4 x 700 mm **W12 Hardened steel rods of 12 mm diameter** - for the Z axis rails - 2 x 750 mm **TR 1203 Trapezoidal lead screw of 12mm diameter ad 3 mm pitch** **Bearings:** - 4 x **KP001 - 12mm bearing** - these hold the lead screws - 8...

The table balances fairly well with Part E feet, but adding the weight with Part F makes it a lot harder to knock over.The settings are the same for either:PLA0.8mm nozzle0.4mm layer heightInfill: 40% cubic2 perimeters Whichever version you choose,...