jacking castors side mount 3d models

Ender 3 side spool holder fortified with added rigidity to minimize deflection.

These are designed for and verified with the case here: https://www.thingiverse.com/thing:1815268 but it should also mount to any of the designs that case was remixed from. I wanted a compact solution to attach an ADSB SDR to the side of a Pi 4...

This updated spool mount shifts the spool to the lower side position on the printer, enabling optimal filament routing into the extruder for improved performance. To maximize structural integrity, I designed this model with 4 T slots that provide...

This insert will repair the Western toilet side mounted flush lever. I made this model to replace the plastic insert behind the chrome flush handle on my Western Toilet. The old white plastic one cracked up. The replacement assembly is less than...

My UP BOX was missing the side cable holders for the Y axis and side button cables. This is a bolt in bracket instead of the clip in style. I used 3 total. ...

This is a central mount for the XT60 on Martian 2.

This enclosure is designed to be mounted vertically in one of the outside corners - upper left rear (version 3) or lower left rear (version 4) is recommended, but other places might suit your needs better depending on cable routing and power supply...

The Block mounts on the left side of the middle table and has 3 screw holes to fasten it in place. Middle table is suggested for multi spool if running more than 1 printer as you can feed filament both directions (up and down). The Left & Right...

The enclosure is designed to be mounted vertically in one of the outside corners - upper left rear (version 3) or lower left rear (version 4) is recommended, but other locations might suit you better depending on cable routing and power supply...

Needed a mount for my new 20W laser with a new PCB. ...Didn't like the way Ortur showed how to mount it on the gantry so I made a custom one in Fusion 360.Hope you like it!

This mount is Ver.3 (Insta360GO for CRUX35). ... 20degrees -> 25degrees -> 30degrees Tilt 5 degrees more than Ver.2. Slide Insta360go into this mount and secure it with a rubber band. ... This is based on data from My_Room, thank you!

Spoolholder Mount for SV06+ to mount the original Spoolholder at the lower frame of your Printer.Extra Material needed:1x M5*20mm Bolt(Used Countersunk but Barrel would be better)1x M5 Nut

... Phone Mount Plate. ...Female Component Available Here: http://www.thingiverse.com/thing:30104. Version 1 Is Too Tight, Failing to Accommodate All Universal Mounts. ...Recommended Version 2 Features Reduced Dimensions and Inner Bumps for Improved Fit.

This file fs for a Wyze Pan mount to watch your 3d prints while they print as an alternative to the Pi cam. ...All you need is a 1/4-20 countersink bolt to mount everything together.

This mount is Ver.4 (Insta360GO for CRUX35). ... Tilt is about 30degrees. It weighs about 2 grams. Slide Insta360go into this mount and secure it with a rubber band. M2*15mm screw is required. ... The Jello improves slightly.

The filter side demands two #6 wood screws (each measuring 3/5") on one side and two M4 30mm screws on the other side. ...It is essential to note that the two holes on the filter side might require drilling holes in the enclosure for added support, but...

Customizable desk mount designed specifically for the HTC Vive Port Box, allowing for effortless installation on various desk heights.

Remix of DroneDaddy's mount to fit my existing setup from RaffoSan https://www.thingiverse.com/thing:2477180

Mounting brackets for GENIMO Cordless Cellular Shades so that you can fit them into windows with curved tops

Original files you will need: https://www.thingiverse.com/thing:3095730 And use this thing to mount on the right. ...

A firm left size display mount for a creality 12864 display on an Ender 5 (pro, plus)

Human: The HE3D K200's standard endstop mounts are perfectly adequate but they pose a problem when trying to create intricate shapes due to their acrylic construction. Consequently, these mounts sacrifice some Z-height, amounting to a couple of...

... tail and brake lights. ...Unfortunately, only standard mounts were available - designed for attaching to a case or similar component. Since license plate mounts were out of stock, I devised my own plan. ...These custom-made mounts work flawlessly.

A simple and easy way to mount a DC switch to a panel, specially if you can't mount it through the panel due to the panel thickness.It only uses one M3 screw for mounting so it is very compact.Print with 100% infill and 0.2 layersThe FreeCAD 0.20...

... block for your pistol with a charging handle. ...Taken from the V7 TakeDown kit. Print each piece, slide the charging handle through its mount. Once the pinhole presents itself, insert the CH Pin. Using the mounting pins to mount to your pistol. ...

To avoid tangled cables, engineers designed a solution to securely attach fans to one side, preventing pesky wire tangles during operation.

In the same way of my other remix for my Oculus support, I made this one to fit my side panel under my desk.

I couldn't use the regular bracket for the right side,remixed this one, shorter and uses less filamentNeeds T nuts

A compact mechanism is deployed, utilizing a third tab that seamlessly integrates into the side rail, effectively replacing traditional fasteners such as bolts and nuts.

... for added stability. ...Originally, a single side support proved too flimsy, as jostling cables caused the laptop to slide out and potentially fall. ...With these side supports in place, the Air drops down securely from above, safely held in position.