j head 3d models

Tips in any amount are appreciated: https://www.paypal.me/satgod First: This is a remake of Loopers Ord-Bot J-head mount I have cut the top off to get rid of the direct drive extruder and make room for the bowden connector If your using the E3d v6...

Tips in any amount are appreciated: https://www.paypal.me/satgod First: This is a remake of Loopers Ord-Bot J-head mount I have cut the top off to get rid of the direct drive extruder and make room for the bowden connector If your using the E3d v6...

This fan mount is my first attempt for Wades Extruder paired with a J-Head nozzle (second try as the initial one went awry). It features ventilation for the J-Head's body, designed for 60mm fans. The mount can be easily installed or removed without...

I've come up with my first fan mount for Wade's Extruder with a J-Head Nozzle - my second one, actually, since the first attempt was a bit of a disaster . The fan is well-positioned to ventilate the body of the J-Head. It's designed to work...

Additionally, there are generic models for the J-Head with and without cutouts for thermistor wires, as well as specific models for the MK V and MK 8 versions with heaters and axial thermistors. ...You'll also find a STL model of the silicone sleeve...

This design is optimized for attaching the affordable V5 bowden hotend available on Aliexpress with a 24mm cooling fan. ... https://www.aliexpress.com/item/E3D-V5-Bowden-J-head-Hotend-12V-for-1-75mm-3-0mm-remote-Extruder-with-cooling/32871485743.html

Fan Mount J-Head V5 (25mm) With Cooling System Installed The latest iteration of this item boasts significant upgrades over its predecessor, featuring a larger size that's hard to miss. ... This sleek design now incorporates a convenient cable tie lock...

Included are effectors that support: Single & dual J-Head, Single & dual E3D-V6 and Lite6, E3D Kraken, Printrbot Ubis. The Ubis, E3D, and J-Head hotends feature a standard Kossel Mini effector radius of 20mm. However, the Dual J-Head and E3D-v6...

So, I ended up using a "J-Head MK-V Hot End" instead (for example, “http://www.ebay.com/itm/261990496377?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT”). This change caused some problems, but I solved them all and am now sharing that...

The provided STL molds include options such as: 0) two casting molds with the heater cartridge entering from either 4 sides on the right or 2 left and 2 right; 1) a generic J-Head with no thermistor wire cutouts; 2) a generic J-Head MK V with heater...

Print a 50mm fan duct designed for Prusa Mendel V2 x-carriage and J-head. Note that this design may exhibit some polygonal features, but it should still function effectively. A test model is included to ensure accurate nozzle sizing for your specific...

This is a design for a J-Head Mount Alternative specifically crafted for the Greg's Wade's Geared Extruder.\nMounts used elsewhere tend to yield and bend under tightening, which this version is built to prevent; instead, the screws actively reinforce...

This is a custom-designed 3D printable mounting system specifically engineered to securely attach the J-Head 12 HiFlow extruder directly to popular CR-10 style printers, as well as other machines featuring identical carriage designs found at...

I enjoy the Groovemount (J-head), I3, and Pneufit (1/8) products. Feel free to test them yourself! Check out these videos for a 5-minute demo: [link 1] [link 2]. After using it for two weeks, I can confirm that it performs well. ...Enjoy!

Included is effectors that support: Single & dual J-Head Single & dual E3D-V6 and Lite6 E3D Kraken Printrbot Ubis The Ubis, E3D, and J-Head hotends have a standard Kossel Mini effector radius of 20mm. The Dual J-Head and E3D-v6 effector have an...

The J-Head originally designed for is quite expensive and not commonly found on Aliexpress, which sells much cheaper all-metal hot ends that claim to be e3d v5 clones - they're also known as J-Heads. The mounting collar on this clone J-Head is...

I've designed a few effectors for my Kossel Minimax (a Kossel Mini derrivative) to hold various hotends. Included is effectors that support: Single & dual J-Head Single & dual E3D-V6 and Lite6 E3D Kraken Printrbot Ubis The Ubis, E3D, and...

With an impressive heat range of up to 250C, The J-Head Lite V2.1 ensures accurate temperature control through its precise Honeywell 100K ohm thermistor. Weighing just 1.2 ounces, this compact extruder measures approximately 2.6 inches in length. To...

Assembly instructions include: (1) attaching the M3 nut to the nut capture on the bracket, (2) mounting the bracket onto the shroud, (3) installing the fan, (4) securing the assembly to the extruder, (5) wiring it up, and finally, (6) experiencing...

In order to solve the issue of extruding ABS through my J Head MkIV nozzle, I opted for installing an active cooling fan while printing. To accommodate smaller prints (below 50mm) on my X-carriage, I designed a minimalistic offset mount and guard.

... micro servos and attaches to the base plate with holes that are 50mm apart. The central 17mm cut-out accommodates extruders up to 16mm in diameter, including E3D and J-Head models. ...On a Prusa i3, this setup doesn't hinder X axis movement at all.

This set of 2 plates combines GitHub components for V4.6's SmartRap, specifically designed for RAMPS and J-Head configurations since they are my current setup and I plan to upgrade with these advanced parts. Using ABS for printing has revealed...

To install a makergear hotend or j-head on the X-carriage of the Wallace, print and place the plate beneath the extruder; this modification is necessary as the X-carriage is too high without it. Additionally, the plate features a 40mm fan mount for...

Human: I was really impressed with Biomushroom's j-head design featuring bracket so i decided to re-work it with a 3mm filament hole and adjust the pnumatic coupling hole to work seamlessly with a 1/4th inch coupling. I relied on indieflow's scad...

In an update, a new model was added that facilitates wire running from the J-Head. Originally designed for a Gregs/Wades extruder, adjustments were made to fit it perfectly. The mounting plate was removed in favor of screws and holes were raised...

This is my project of a Direct drive extruder with a solid mount J-head V6 and cooling system that features two 50mm fans and one 30mm fan for the radiator. Parts list: Bearing 624RS x1 Some M3 screws M4x12mm screw x1 Two 50mm fans One 30mm fan...

A 1/8 BSP screw is used to attach the effector directly to the Bowden J-Head hotend, eliminating the need for retainers. The depth of this screw is 2.5mm. To install a 4mm PTFE tube through the end of the BSP/NPT push fit adapter, drill it with a 4mm...

# MK8 Carriage on 3D Printer Under MK8 + V5 J Head Hotend Thrives in Plastic Testing The carriage on a 3D printer, paired with the MK8 and V5 J head hotend, is performing remarkably well under plastic testing conditions. The flexible design of this...

### GEEETECH G2S single hotend j head MK6 mark 6 hotend adapter ### Description: mount made for turning to two to one single hotend on geeetech 3d printer, ABS recommended but it works fine with PLA, compatible with MK6 j head hotend. It...

If you simply want to print using 1 J-head bowden setup, this coupler is sufficient. The kit contains a fan duct (the heatsink cooling fan serves as the part cooling fan). The fan duct comes in two pieces (print separately and press together as...