ir3 v1 3d models

MKS Controlboard Case -- I designed it around mine which is the MKS Gen_L V1.0. It may fit other MKS boards but I'm not sure. Also there's a couple versions depending on what you may want as far as wiring options. <strong>Spool Holder</strong>...

Update:16_08_19 B EZABLTouch Plate_V1 incorrect hand - have uploaded EZABLTouch Plate_V2 Update:16_08_19 Uploaded a WIP fixing plate for a EZABL sensor. This was a member request with a 18mm mounting hole specified. Never used one so this is...

Air holds v1 - these hold 6mm tubes, I chose aluminum, but copper works fine too. They bolt below the board on each corner of the triangle. Dist v2 - This air distributor and retainer for water cooling tubing has a 10mm inlet port and 3x 6mm...

You may also be interested in my Dust Collection Port (v1.0) for DIY Router Table - designed for 2.5" hose from Vacmaster shop vacFeatherboard for woodworking, no supports needed, with M5 & M6 options for knobs & track slides - plus ¼" bolt option...

In V1 and V2, you had to direct your airstream almost perfect to hit any of the higher notes, it was very tricky. This will hopefully fix that. I added a flattened portion to the back of the embouchure hole, to hopefully get your lip closer. ...

This is the screen frame i printed https://www.thingiverse.com/thing:4802109 The Wyze cam mount https://www.thingiverse.com/thing:4117708 The raspberry pi case https://www.thingiverse.com/thing:3673994/files (You'll need ARpi_4 top case with fan40...

VCC 5v – Red (although I'm only supplying 3.3v) GND – Black A (Signal) – Green B (Signal) – White Currently this is how I have mine wired up on a BTT Octopus v1.0 MCU board. VCC, GND & B (Signal). I installed a 3Pin JST connector and plugged it...

I think the V2 part cooling duct will be way more effective than V1. UPDATE After installation I have noticed that some parts need a little rework so I have replaced some parts with V2 versions of each. The home park position is off the print bed by...

As per Umbilical Mod v1… This is my combination design for mounting the Huvud board Canbus to the side of a Bondtech LGX extruder, with stepper motor cooling, umbilical chord mod removing gantry drag chains, shifting x and y stop switch locations,...

DIY at your own risk!USE V3 FILES, just leaving V1 and V2 up for archival's sake but they're basically unusable compared to V3. UPDATE 3/25/24: Design Has Been Finalized! After taking a break for a month or two, I've come back to it and finally...

I can no longer find the owners of "reparaturplatte.stl" and "Fan_Guard_v1.stl", sorry; if anyone will enlighten me here, I'll give proper credit. The LED bezel is mine, the "C64Badge.stl" is here: https://www.thingiverse.com/thing:4218692/files,...

once its put all the way on if u printer v1 the original bolts will work for holding the bracket on but if u used v2 u can use the original bolts to hold the mount on but also use it to put pressure against the roller holder so it cant slide out of...

I used this one: www.amazon.com/gp/product/B000GTMUUIx2 Female Spade connector appropriately sized for the toggle switch you buy (the linked switch uses 6.37mm (0.25in) connectors)x2 Female Spade Connector 4.8mm (0.189in) to attach to the Mini's...

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

The v-core arms used are from https://www.thingiverse.com/thing:5131325 by MFBS and has a https://creativecommons.org/licenses/by-sa/3.0/c licenseThe VenterMech is from...

Files ending V1 are updated files.These guides were created to stop the edges of the CR-30 conveyor from curling at the edges mainly when cold, and also to ensure that the printer stops should the belt tracking go out of alignment.All parts and...

Two springs are used in this "V1" design, the first is a 20mm compression spring used in the bed of common 3D printers like the ender 3 https://www.amazon.com/gp/product/B07V6YCYP5 the weakest one in the kit. The second is a common 23/64" x 1 3/8"...

I believe braingame26 had indicated his was based on the 25.4mm dxf file from V1 Engineering. I compared this against another version of this plate apparently based on 25mm dxf file; this one in particular: https://www.thingiverse.com/thing:4789218...

V1 arm is fine too, but there is a risk of collision with some models of head in very rare cases of high and wide prints prepare all parts power off the printer UNPLUG POWER CABLE! unscrew PSU from the frame remove plastic cover of PSU cables ...

They are all denoted v1.2 Changes: Reduced the depth/length of the "wings" going out backwards as they could hit the z-max endstop holder and/or screws in some instances (not tested on printed cases). Made room for 20mm M4 screws and generally...

From v1.1 onwards, the Runner_Height_Multiplier setting enables you to adjust the thickness of the runners. You can increase this value to increase the durability of the chest. We recommend you save a preset in OpenSCAD for each drawer and chest...

this model is based on real data therefore this is a realistic buildings and streets setup of Tbilisi, Georgia 6 building groups are setup so that you can add variety to buildings (color materials and/or textures) Groups can be turned off/on UV...

V1 arm is fine too, but there is a risk of collision with some models of head in very rare cases of high and wide prints prepare all parts power off the printer UNPLUG POWER CABLE! disconnect low voltage connector (2 wires) unscrew PSU from the...

It is now fixed. UPDATE 02-10-21 I added the 2x2-v1.stl to the parts list. I also posted my Husky Container rack parts here - https://www.prusaprinters.org/prints/56006-husky-container-rack Great place to store all of your containers UPDATE...

This is at 18.28 mm for the V1 shroud and at 16.78 mm for the V2 shroud. After switching filament colors, the nozzle may not be primed and the first bit printed may be under-extruded, so to compensate for this, I always add in a little cylindrical...

Electronics 1x Bigtreetech SKR 1.3 mainboard 4x TMC 2208 Stepper driver 1x BTT TFT24 or BTT Mini12864 display 1x Mean Well LRS-150-12 Power supply 1x SSR Relay 8A - Hoymk SSR-D3808HK 1x 16mm anti-vandal power momentary switch - 110/220V variant 1x...

And so my Eustathios Spider V1 variant, named due to the color scheme, was born (https://github.com/eclsnowman/Lien3D_Eustathios_Spider). I built the Eustathios and fell in love with the smooth operation, clean prints, and overall reliability. So...

Use either, they'll both work. Updates 2018-09-19 Fix cutouts for Cherry MX Stabilizers 2018-10-13: v1.0.0 "Final" release version. Fixed Fusion 360 file by rebuilding the left-hand side; both sides are now in matched drawings/steps, and easier to...

**Edit: 5-8-19** The bomb tray has had its clearance increased (**bomb-insert-v1-clearance-fix.stl**). If you've already printed Base2, please use this file. If you haven't printed Base 2 yet or if you prefer the standard thicker walls then download...

I do recommend the v1.2 cup that is shorter. but other than that it worked to my satisfaction :) Slide 1.4: Updated the slide to a slightly smaller size, seems too much tolerance (1.4 slide) June-20-2021 =========== Slide 1.2: Replaces...