ipod touch 3rd gen case 3d models

Made to replace the little compartment with something a bit more useful. It is angled down and towards the driver for better access and visibility. There are two models, one with factory sized openings, and a blank to cut out your own to add custom...

/!\ UPDATED 09/2021 /!\ Addition of optional rings GG3_V2_Optional_Joint_1.stl -> need for supports GG3_V2_Optional_Joint_2.stl -> need for supports GG3_V2_Optional_Joint_3.stl -> need for supports GG3_V2_Optional_Joints.stl (3 in 1) -> need for...

These filler panels replace the bulky factory cargo cover mounts. If you no longer use or don't have a cargo cover these are the perfect way to clean up the look of your cargo area. ...They can be left as is or used as a place to mount other...

this is a spacer to fit oversize 6.5 , .drill to fit and its slides over the the rear door adapter Adapter 138mm ID spacer for 134mm hole Spacer 148mm ID 170mm OD To install . ...install the 4runner adapter plate file above , then...

The 3D model was created on real base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: *.max (3ds Max 2008 scanline) *.max (3ds Max 2008 vray) *.fbx (Multi Format) *.obj...

I've long been trying to come up with a solution for my keys that combined my stock fob and my aftermarket remote start. I finally just forced myself to learn how to 3d model and designed my own. I am using the stock buttons and silicone buttons...

Print with prelude facing down I used a raft for best results.

Here's a modified version of the design that accommodates an IT power supply by increasing the size of the hole. I made only one alteration to the original design, found at https://www.thingiverse.com/thing:3273420, to allow for the use of an IT...

Triple Switch Plate Fits Perfectly in Cubby by Steering Wheel. This premium switch plate is specifically designed to fit tall Toyota push-button switches. ... The "new" design provides a precise centering of the switches vertically within the cubby...

This is a redesign of Litesaver's original cupholder. This cupholder has been redesigned to fit larger cups. The original could only fit small water bottles and cans. With this new redesigned cup holder, you can now fit much larger drinks from fast...

Here are many parts to mix'n'match. I did not print-test every single model and combination (e.g. smooth base and smooth top work fine). One primary goal was to not cover the light ring, so I didn't. :) Oh, I do not expect anyone to try the lattice...

Remix of my remix of the original by leefla https://www.thingiverse.com/thing:3516527 https://www.thingiverse.com/thing:5280232 About a year has past and I'm starting to get better at this :) My first attempt has not survived the year,...

Remixed from the following models: https://www.thingiverse.com/thing:3224790 https://www.thingiverse.com/thing:1873213

Helps to keep objects from sliding around in the upper portion of the glove compartment. Fits a third generation Prius perfectly and likely also fits the second generation as the dimensions appear to be very similar. For added stability, use rubber...

Remix of my remix of the original by leefla https://www.thingiverse.com/thing:3516527 https://www.thingiverse.com/thing:5280232 About a year has past and I'm starting to get better at this :) My first attempt has not survived the year,...

<p>Here are many parts to mix'n'match. I did not print-test every single model and combination (e.g. smooth base and smooth top work fine).</p> <p>One primary goal was to not cover the light ring, so I didn't. :)</p> <p>Oh, I do not expect anyone to...

I designed this support bracket for an issue with the air vent in my Toyota Tacoma. The air vent blades would no longer move together in sync. This piece had broken. The new assembly from Toyota was very expensive. Its a bit hard to get onto the...

I found the design by the original designer to be great, but unfortunately a little unstable. I designed this base plate that the housing and legs sit in. ... The echo clock is simply glued into the insets.

Had difficulty attempting to fit 6.5in speakers. ...This is designed for 5.25in speakers and requires significantly less work to fit these in the rear door compared to a 6.5in.

I only raised the Stand. ... This is a remix from https://www.thingiverse.com/thing:398515 This is my very first post so be lenient :)

This part slides onto the existing volume knob. For me, the friction fit was perfect with my print - no glue was used. Your fitment results may vary though. It may wilt during the summer heat. ...We shall see.

WORK IN PROGRESS. Uploaded version has switches spaced just too far and won't fit in cubby hole. ... Took Cracked1's cubby switch panel and made it for 3 small size toyota switches, fits and works perfectly fine.

I designed a new cupholder for my old, failing one in my '97 Toyota 4Runner. It's specifically made for holding a tapered cup, like those used by Starbucks, and features a single cup design. The core render takes into account the locking tabs that...

Use this simple jig to ensure your new Lokbuild print surface is installed perfectly to your Cube3 print plate. You'll need to print 4 of these and a 203mmx203mm Lokbuild print surface. Lokbuild is a MUST have for anyone hoping to print ABS with...

Hack job of a remix of Lefla's Amazon Echo Dot mount. This is for a horizontal outlet, letting the echo still hang below it. ... This could be cleaner, and could be simpler, but it was a quick hack and it works.

Replace your lost or broken heater/AC control slider knobs with new 3D printed replacements. ...These knobs are 3D printed out of strong and temperature resistant PETG plastic.

I reinforced the existing brackets on Leefla's original outlet, giving them a substantial boost in stability and reliability.

I took the awesome tie fighter by https://www.thingiverse.com/CaiotE and made one small tweak and added one new piece: 1) Increased the size of the square pegs/slots for wing attachment, to add a little strength. 2) Created a base to set the...

Simplified version of leefla's design, made to hang from the top of a dresser. Rather than designing the correct sized hook, I left that part of the model flat, so that a hairdryer can be used to soften the plastic and then mould it by hand...