ipod touch 3rd gen case 3d models

Fits 1st gen Tundra CVs. M<ay need adjustment for proper clearance and alignment.Requires the spindle to have a bolt to interface the uniball. ...This can be done by taking the stock LBJ, cutting the ball joint out, and welding a bolt into where the...

Designed a simple case to hold a Samsung S7 touch for transport, together with one (possibly both) USB-cable. Comes very handy, whenever you need something to carry or store that drive for transport. I use it in my backpack with loads of stuff in...

This is a case for a 7-inch touch screen that features a sleek design with a high level of customization. The touch screen itself resembles the one shown in this image:...

A case for using the Kobo Touch e-reader with a BlueFly vario as flight instrument. The vario used for modeling was a BlueFly TTL v12 but I tried also a v8 version and it fits perfectly. You will need two M4 screws to hold the lid, better if you...

After failing to find a well-designed, simple (low part count) kit to run Octopi, that didn't also require a bunch of different screws, I designed the Pi Touch Case. Bring your electronics and 4 M3x10mm screws for the touchscreen’s factory mount and...

You can find 7-inch touch screens available to purchase specifically designed for use with the Raspberry Pi.

... the mounting holes on. ...Couldn't find anything else on the internet, so here's what I came up with in tinkercad. Printed in Resin, since my FDM printer was dead in the water until I could get the CR-Touch working again. ... Your mileage may vary!

Originating from the Apple Design Guide, specifically version R8, this information was confirmed through precise caliper measurements obtained from a second-generation device.

The Center console cover designed for a 91 Camaro should fit 82-92. The cupholders are sized to fit standard 12 oz cans and small bottles. the installation can be challenging and did require a small amount of trimming of the lower console components....

This is a rear camera mount you can use to relocate the backup camera in your Tacoma... I have a "flat" camera mount and a 30*. this is the 30... this part has been 3d printed and mounted on my truck and has been working great so far. I can also...

I opted for a Wizgear magnetic phone mount, ditched the original tape and went with epoxy instead. I'm confident the tape would still work fine in place of epoxy, but I wanted better heat resistance. The mount was designed with a 10-24 machine screw...

I fell in love with this design https://www.thingiverse.com/thing:3361240, but my printer struggled with support issues and couldn't bring out the fine details, so I started from scratch and made it modular. ...I used this design for the Wonder Woman...

Modified to print with no supports or raft to keep the face smooth. Print with face on build plate. ... Also made the teeth more aggressive for better grip.

This stand elevates your Apple TV box by one inch, providing a sleek and streamlined profile while minimizing waste through its hollow design that requires minimal filament usage.

Gauges support for third generation Camaro 1982-1992 in place of ashtray.

I've always been fond of the charging dock on the original Moto 360, which is why I designed a comparable dock for the latest version. The charging cradle of this new smartwatch slides seamlessly into place within the dock. ...Images below compare it to...

Tail tidy for my sc650 just to hold the turn signals

This is my inaugural post, marking the beginning of a carefully designed project. I envisioned creating a statement piece that would free the Echo Dot from its surface-bound existence while retaining some semblance of its original design lines. My...

A remix of the Tacoma Coin Holder by rvsf0219, i removed the TRD logo on the top and replaced it with a Tacoma logo. ...Enjoy!

Updated to account for slightly smaller size of the AppleTV. Added front bar to better distribute weight as the original tabs broke for me (could be my cheap PLA and lack of printing skill). Added hanging tab in back of model to work with...

MKS Gen v1.4 casing system.

Case for the 10th gen Kindle Paperwhite.

... was created using Customizer! ...(http://www.thingiverse.com/apps/customizer/run?thing_id=162367). The specifications used were font size 19, label text as '3rd', an end space of 1, the 'write/Letters.dxf' font style and a letter spacing of 1.

... you can adjust parameters such as font size (set to 19), end spacing between characters (set to 1), and letter spacing. The chosen font is "Letters" and will be saved in the .dxf file format. The label text for your customized item will read "3rd".

The P90 is a MASSIVE case and the use of the glass just was not necessary for me, but the case wouldn't stand up straight with just the 2 plastic legs so enter the 3rd leg. I revised this a few times, the added cylinders inside the print and...

A basic stand for holding the Airpods Gen 2 case.

Case for MKS Gen 1.4 Board Demands an Eighty by Eighty Fan Requirement.

I created this mount because I needed a way to securely attach my Raspberry Pi to my printer, all while keeping the same protective case in place. Noticing that the printer had mounting holes on its back panel, I decided to use those as a starting...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankGearAngle = 15 MusicCylinderNameFontSize = 8 midGearAngle = -5 crankAxisCutAwayH = 4 musicCylinderTeeth = 48 crankAxisHolderH = 1.55...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankGearAngle = 15 musicAxisHolderH = 3.4 GENERATE_MUSIC_CYLINDER = 0 gear_hold_R = 4 MusicCylinderName = Whatever (Elliott Smith) FOR_PRINT = 1...