iphone 6s plus 3d cases

There are however, various integrated supports and sacrificial layers that will require cleaning off after printing (refer to the Installation Guide and the Part Preparation section).2.All parts were printed with PETG, 30 to 40% infill with 3...

###Anet A6 E3D Hemera Carriage This carriage design for the Anet A6 3D printer is suitable for both the E3D original Hemera and the shorter and lighter E3D Hemera XS extruder. The parts are added to equip the Hemera with the E3D Revo, V6, Volcano or...

Design is done by 3D-modeling using CAD Pro Engineer, prototype engines by using Lost Wax moulding and / or Rapid Prototyping , test runs and mass production in our facilities. 3W – History 1985 Introduction of the first 2-stroke gasoline...

There is no need for tension here other than to prevent the front mount from being loose If the printer is mounted on a base plate: Fasten the motor mount to the base plate with a screw in the slotted hole on the motor mount You may need to check...

 (The combined slop of the 3D printed parts will give you roughly +/- 0.5mm of tolerance on your cut.If you buy hex on sites like Online Metals that sell in 12" increments, then each 12" will get you two cut hex rods. Preparing the JigThe jig has two...

If you use the F3D files, go easy on me as I've only been using Fusion 360 for a month and its the first time I've ever been exposed to 3D modelling. I'm sure there are faster, more efficient, and proper way of doing things as oppose to the way that...

The Greatest view this model has are opposite from the conventions or typical 3D models. All the juicy detail work is on the inside. The Babylon Project was beautiful to the eye, and yes, it’s a Diplomatic station. This isn’t. It’s a modular city...

... HBP modification that if you use the 1" thick supports you have to set the z axis to 245 but with the 3/4" version you can do the full 250. I personally will stick with the 1" version and loose 5mm to give my bed more support. Category: 3D Printers

Taylor and Dan the 3D Printing Dad, who were inspired by the brilliant toymakers of your childhood, comes a racing toy that you can print at home and race on any smooth, flat surface! Print enough for you and your friends and race each other! Or...

based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 All of which is very much derived from the excellent design here:...

(see photos) The heater cartridge was also sliding out a bit and caused a high temperature spot, you may want to take a look yourself.Changelog:v2: 2020/05/234010changed the angle of the duct to hit below the nozzle, not the tipchanged focal position...

Join our Tribe or Patreon to receive amazing 3D printable miniatures set each month for a very special price!  Save big on the complete Bronzeclad Greatgoblins bundle, which also contains pre-supported files for each STL. Please check the images to...

The shims will directly contact the printed part; for that matter the bore diameter for the shoulder bolts has been reduced from 5,5 to 5,1mm (you might drill that out if it does not fit) You will also need all the screws to attach the parts to the...

Pixracer https://s.click.aliexpress.com/e/_ABW87n Pixhawk bundle https://s.click.aliexpress.com/e/_AnT7ln 1 battery Li-ion...

Use at own risk, you may have to reprint them later.------------------------------------------------------------------------------------------------------Voron Stealthburner Beta for Creality Spider V1 hotend with Orbiter 2.0 extruder (direct drive)...

Think of it as the gauntlet is laid down and a super fun challenge in 3d spatial orientation! Oh and don't superglue your fingers, eyelids, or other body parts to various things, it's not as fun as it sounds. You may want to try using sticky tape...

Note: The G code files are set up to print with PETG material.2) Procure the commercial hardware from the parts list, M3 screws, square nuts, hex nuts, and 4mm OD x 2mm ID Teflon tubing (or re-use the existing buffer tubing).3) Cut the existing 10...

If you have access to a 3D printer, it would be best to pre-print some of the parts in the download, in particular the BLTouch holder and extender plinths. The BLTouch v3.1 probe (raised using M280 P0 S10 in GCode terminal) will need to be set at...

This push-to release mount for the Google Chromecast TV remote, stores the remote under a coffee table, and a simple push on it's obscured base, and it ejects the remote for easy access like this:As well as being a cool way to keep your able that...

Send me a message if you have a particular chess set design that you would like to see as a 3D model. I am always open to new ideas. Although I have steered clear of the Staunton design, I am considering adding the more popular formats, like the 1959...

7 - All items in the console are 3D printed, optional decals are attached to the sides of the model. A JPG file containing the decals is included in the pictures section. 8 - Small note: the back_wheel_attachment/left/right might have a few small...

Each Skittle knocked down equals one point.The first player to reach a score of 101 is the winner.You can make up your own rules. When I have played the game with my 3D printed set I have found the skittles nearest the post are difficult to hit...

The input data you provided seems to be a list of tuples, each representing a point in 3D space. The format is as follows: * The first element in the tuple represents the x-coordinate. * The second element represents the y-coordinate. * The third...

For me PETG works perfectlyLayer Height: 0.2mmPerimeters: Cap 4, Label 2Support: NoAttributionBefore I designed my own parts I bought the design for the Anybox V2 from Marian. This is a great and cost-optimized box, with perfectly designed parts and...

I have no idea what would be required to get dual-extrusion working: it might work with some minor changes, or it might be impossible to get working. 2020-02-14 update: It looks like eugr has figured out how to get dual-extrusion working, so if you...

There are several 3d printed threaded parts. The internal threads should be cleaned out with a 6mm X 1mm tap. If you don't have a tap you may be able to use a 6mm bolt with a groove dremeled into it. I haven't had to use a die to clean up the...

Join our Tribe or Patreon to receive amazing 3D printable miniatures sets each month for a very special price! Save big on the complete Raid at the Temple of Ifrit bundle, which also contains pre-supported files for each STL. Please check the images...

based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 All of which is very much derived from the excellent design here:...

This file you can send to your printer and the tower should be printed out with the different temperature settings. Print instructionsCategory: 3D Printing Tests Summary [2018-03-28] Useri_has_it found out that the only thing to make it work...

Microstepping is not saved in the EEPROM, that's why this needs to be in your startup gcode. CREDITS : Prusa R4 extruder : https://github.com/prusa3d/Original-Prusa-i3/tree/MK3S CAD model for Bondtech gears :...