ipd oculus quest 2 3d models

I followed this reddit post to put my broken Elite battery on my Bobo VR M2 halo strap.  I wasn't happy with the taped together straps, so I designed and printed a replacement strap. I designed this with my printer tolerances in mind and it's a good...

Modification of the original model for use with https://www.thingiverse.com/thing:3653631

I made Light Blocker that Light leakage from nose gap. ...

This is a battery holder for the anker core 20100

Name: Air Stock 2023 "Ready to reserve and use with ease and peace of mind! Gun stock VR is an easy-to-use device and a whole new VR gaming experience like never before! Gun stock VR is designed to make controlling weapons in virtual reality...

6mm pipe x6 30mm fan x1 usb cable x1 DONE!~~ Hope Enjoy ~

Customized version of https://www.thingiverse.com/thing:4791788 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4791788

I wanted to Add a battery pack to the Elite Strap thing. I really like the design in for adding a battery pack with the following thing (https://www.thingiverse.com/thing:4070533). ...Quickly and dirtly combined the two together in tinkercad The...

For the connector, I used Lego Technic Pin (Black, part 2780). TAKO is a quick solution for when we want to experiment with extra I/O or haptics in custom VR experiences but also need the position data for navigation. ... The size is designed for...

Original models didn't fit my DAS, so I've adjusted them a bit so they fit better. In addition powerbank holder remade to fit Xiaomi Redmi Power Bank 10000 mAh - you'll need some 3m doublesaded tape (make them small) for it not to wiggle to right...

Didn't find any adapters that was perfect for me so created my own. Inspired by: https://www.thingiverse.com/thing:4654892 Like the cable going behind/inside. My design is however only reusing parts from: ...

Fixed this to need no support

I was using the Clip on battery mount from @ChamKyoYuk and was well happy with it. But then I had the need to use powerbanks of different sizes. ...I the made this one to use with velcro strips.

I came up with a battery holder for the Anker PowerCore10000, but getting the whole set up in my case required putting the battery in a bag and letting it ride the lenses. This would not do. So I spent 10 minutes in 3D Builder and hacked on the...

You need some 15mm wide double-sided velcro strips to hold the power bank and the mount. I'm using xiaomi 5000mAh (perfectly balanced) and 10000mAh (too heavy) power banks. ... Happy Gaming！

remix for some extra style, i used EVA foam for padding and command hooks for attachment to side arms.

After trying the link cable with the elite strap I noticed that the cable liked to come unconnected easily. Then I got to work designing this simple strain relive mount that attaches to the side of the elite strap. ...Please post likes, makes, and...

Made a no-support version. Cut the ears off and printed them separate. Glue them in afterwards. ...Tiny seam, but saved hours of print time and filament.

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

This is a controller arm for the amazing mech VR game "Iron Rebellion" For assembly you'll need two rods of 16mm in diameter and about 360mm in length, one rod of 16mm in diameter and 80mm in lenght, six bolt of 5mm in diameter and 20mm in leght...

Remixed Przemoc's model by blender reduced the curvature of the face and nose area

I wanted to Add a battery pack to the Elite Strap thing. I really like the design in for adding a battery pack with the following thing (https://www.thingiverse.com/thing:4070533). ...Quickly and dirtly combined the two together in tinkercad The other...

<p>This is a replacement for the BOBOVR M2 strap that seems to broke very often like in my case.<br>It is slightly thicker than the original to ensure greater strength.</p><p>I made two versions, one with the screw guide like the original and one...

I was printing and assembling the magnetic gun stock from Teque5 and decided I wanted a fancy muzzle brake. Found CloudyJ84's design and merged the muzzle piece into the base of the dragon head. ...Didn't print perfectly but I think that's more my...

This is a remix of the popular Sanlaki gunstock design modified for usage with the ProVolver from ProTube. - The magnetic mounting has been completely reworked and is „pipeless“, reducing the weight of the gunstock tremendously. - The...

Thanks for the Scan! This is my quick clean up, possible now to print without supports and adhesion is improved on first layer. Further edits like nubs where the buttons would be might be added to make it feel more realistic, possible further cleanup...

After trying the link cable with the elite strap I noticed that the cable liked to come unconnected easily. Then I got to work designing this simple strain relive mount that attaches to the side of the elite strap. ...Please post likes, makes, and...

Use 3 4mm diameter, 40mm length screws or pins to connect the parts

This is a remix of this thing: https://www.thingiverse.com/thing:4768661 However, for this remix you'd neither need a glue nor supports. Also, it is featuring an improved safety by providing an extended controller clamp. The thing is compatible...

I loved the grip from @Bluefreddo, but missed the tang to grab the web of my hand. I'm VERY new to 3 printing and designing, so I did my best to add one and have been enjoying using it. I hope you will like it as well. ... Kudo to Bluefreddo -...