ipad mini photo frame stand 3d models

I desired to capture some photographs of small printed items for tutorials, inspired by photo background stands posted on Thingiverse. However, I sought a simpler design. This photograph background stand is designed for use with binder clips, which...

... A4 sheet. This was inspired by Slepcat's "Paper Clip to set up simple photo background" http://www.thingiverse.com/thing:95180 and HPaul's "Photographic Sweep Stand" http://www.thingiverse.com/thing:106568 . ...Print instructionsCategory: Camera

Stand for tablets, iPads, iPad Airs, iPad Pros or picture frames that are at least nine inches in size. You can also use this model for iPhones or smaller devices if you scale them down to fifty percent. Print Settings: Printer: Flashforge Creator...

Mount for iPad Air 1st Generation, designed to fit the IKEA HOVSTA 21x30cm (A4) photo frame. STL files for the whole frame are included, as well as a two-part split print for smaller print beds down to 220x160mm. ...To print in a the entire frame, a...

Mount for iPad Air 2nd Generation, designed to fit the IKEA HOVSTA 21x30cm (A4) photo frame. STL files for the whole frame are included, as well as a two-part split print for smaller print beds down to 220x160mm. ...To print in a the entire frame, a...

This is a "landscape only" frame for Fuji Instax Mini pictures.

Many of the Instax mini frames on Thingiverse have a bar up on top like a conventional photo frame but this always made them challenging to print correctly. I decided to design a new frame that would make it super easy to swap photos while also...

Display Frame on a Swan Neck Table Holder. ... Frame for LG LP079QX1-SPxx Used Swan Neck Phone/Table Stand: https://www.amazon.com/dp/B074GNPSC7/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

This is a modified version of the "Instax Photo Frame" by o0aaron0o, you can display 3 photos instead of one. Note: It was printed using Cura 4.4.0 with raft and tree supports only. Category: Decor

This is a modified version of the "Instax Photo Frame" by o0aaron0o (https://www.thingiverse.com/thing:344307), you can display 3 photos instead of one. ... Note: It was printed using Cura 4.4.0 with raft and tree supports only.

I didn't find some nice easy to print simple picture frame for Fujifilm instax mini so i draw 5 models. Really easy to print. You can print the 5 frame on a MK3S in one print with no skirt. Their hole in the back to hang them on some finish...

This is an enhanced edition of the "Instax Photo Frame," courtesy of o0aaron0o, featuring the ability to showcase three photographs at once.\r\n\r\nThe production process involved printing using Cura 4.4.0 with a focus on raft and tree supports only...

Supported by gravity and leverage the frame slides over the Home Mini voice assistant and then is leant back to secure it in place. The picture slides in from the top and supported on all sides to stop sagging.</p><p>Print face down with supports...

Alternatively, utilize this design as a personalized photo frame: snip out an image and attach it right above your uncle's visage on the gimbal. This ball has a diameter of approximately 3.6 inches and features movable flexibility in the yoke. A...

small picture frame&nbsp;Print Settings:Printer: PRUSA i3 MK3S+Resolution:&nbsp; 0.2mm Layer Height (0.4mm Nozzle)Filament: PLASupports: None

small picture frame&nbsp;Print Settings:Printer: PRUSA i3 MK3S+Resolution:&nbsp; 0.2mm Layer Height (0.4mm Nozzle)Filament: PLASupports: None

Simple photo frame/tablet stand. ...Fairly sturdy, even with low infill.

The stand is also the right way to close the frame, so that the photo frame and stand become one.Available passe-partouts:1st prizeChampionEllipseForever in our heartsmy loveKeyhole ulala (for over 18 years)RectangleI printed everything on my Prusa...

The stand is also the right way to close the frame, so that the photo frame and stand become one.Available passe-partouts:1st prizeChampionEllipseForever in our heartsmy loveKeyhole ulala (for over 18 years)RectangleI printed everything on my Prusa...

A really simple photo frame/large tablet stand that I quickly put together. ...Fairly sturdy even with low infill.

A really simple photo frame/large tablet stand that I quickly put together. ...Fairly sturdy even with low infill.

Frame for 10 x 15, 13 x 18, and 18 x 24 photos, with table stand, for vertical and horizontal position. Front and back side are printed and easily glued. ... Quickly change the photo through the top slot.

A simple iPhone 4/5/6 and iPad-mini stand that's designed with simplicity in mind. It works effectively with any smartphone, including the old iPad 1 when positioned in landscape mode. The tiny stand also accommodates iPhone 4/4s devices with or...

iPad mini 6 (or previous) drawing or modeling stand with detachable Apple pencil holder. ... The final version is sturdier and more robust than the one you see in the photos.

My first design is a straightforward stand for an acrylic photo frame available on Aliexpress, designed to hold a 254x203mm frame that's 19.4mm thick. This design prints best when oriented sideways. To see the product, visit...

This stand is designed specifically for the IKEA FISKBO series photo frame, and I've personally tested it on frames measuring 10x15 cm and 13x18 cm with excellent results. ...Keep in mind that IKEA often updates their designs slightly between versions,...

It's a simple stand for an acrylic photo frame that can be bought on aliexpress. It is designed for the 254x203mm that is 19.4mm thick. It's best printed on its side. Link to product.https://www.aliexpress.com/item/32896321582.html It is used for...

I bought this digital photo/video frame from Amazon, as a way of showcasing my YouTube videos along with my models: https://amzn.to/3MipBQESome child decided to run past my table, knocking over the display. ...Fortunately the main unit survived, but the...

It's a simple stand for an acrylic photo frame that can be bought on aliexpress. It is designed for the 254x203mm that is 19.4mm thick.</p> <p>It's best printed on its side.</p> <p>Link to product.<br/> <a...

It's a holder for a Go Pro or other Wi-Fi action cameras on an iPad Mini or tablet. The file is in Fusion360 format (.FCStd), feel free to modify if needed. ...If anyone prints this, I'd appreciate photos of the finished product!