ipad handlebar mount 3d models

I've tested a customized GoPro mount specifically designed for Syncros handlebars using Scott 750 and 950 models. This custom version is based on the original design found at Thingiverse, with thing ID 62800. ... You can create your own customized...

... the hose clamp is 10mm wide. This one mounts to the center of the Sargent controller. I have another one that is 6mm offset. Fits my BMW R1200GSA motorcycle but will fit the R1200GS, R1250GS, R1250GSA and many other models with 22mm handlebars.

To mount it onto the handlebar, use appropriate zip tie. Added extra tie off hold for mounting on helmets. Do it at your own risk mounting it to helmets. I designed the mount base on the black diamond astro 250, but it should also work with the...

To assemble this mount, you'll need the following materials: * 3D printed parts * Three zip-ties (also known as cable ties) * Two-side tape If you encounter any fitment issues, please leave a comment so I can address it. You can also modify the...

- The "iPad grabber" part should be positioned on its side with supports holding the mounting tab in place. - The main arm needs additional support around the post that slides into the feet of the stand. - The base should print flat in its...

You can also just print one with the extra arm, and one without to just get that little extra support.This is just a remix of the iPad Air headrest mount, but sized to snugly hold an iPad Pro 11 (Model A19080, A2013, A1934).I have also added side...

You can also just print one with the extra arm, and one without to just get that little extra support.This is just a remix of the iPad Air headrest mount, but sized to snugly hold an iPad Pro 11 (Model A19080, A2013, A1934).I have also added side...

The mount fits perfectly onto my 22.5mm handlebar, allowing a voltmeter to simply click into place and sit securely without the need for adhesive tape. However, users will need to thread their wire through a hole located at the back of the mount, so...

UNIDEN UH45 CB BIKE HANDLEBAR MOUNT Engineered to provide maximum protection for children, this mount is designed with safety in mind. A stretchy elastic hair band securely holds the radio in place, eliminating the risk of it falling out. The...

The mount is designed for use with the "CLICK Hike" light from Quechua, which can be attached to your bike's handlebar. This support allows you to quickly install and remove the lamp by simply turning it 90°. You will need 4 M3 screws (30 mm long)...

Made this function as a 2 piece unit for horizontal mounting of the iPad. Also allowed more space for a slim case and removed a bit of excess material as it didn't need to be as bulky since there is 2 pieces on this remix. I printed at 10% infill...

Here are two wall mount designs specifically tailored for your iPad Mini 2: Each design can be manufactured using a 3.5mm screw. Design Option One: This design features straight edges, making it ideal for those who prefer clean lines and...

https://www.printables.com/model/225617-universal-handlebar-phone-mount-harness-system Universal Handlebar Phone Mount | Harness System For ANY Phone With/Without Cases A, REDESIGNED, simplified version of the mount I use on my motorcycle. **Maximum...

I made this bracket to mount a Specialized Lux light on my bike handlebars and not buy their $30 bracket that should have come with the $140 light. Printed with support. I used a piece of cut open shrink wrap on the bar to provide some...

This mount holds your iPhone 6 securely and attaches to standard 22.2 mm (7/8") diameter handlebars. Unhappy with the existing designs, even when shopping, I decided to create my own custom solution. You'll need two M5x45 SHCS screws along with two...

Mount securely attaches to the handlebar using cable ties or a velcro fastener. To establish a connection between the two parts, an M6 cylinder-head screw and a nut are required, inserted into the bottom part. The nut is inserted before the hex-hole...

I've used this mount with an iPad Air in an Apple leather case and found it to be a secure and snug fit, but other tablets should work just as well. The gap between the mount and the stand is 12mm, so ensure your tablet is under that thickness. The...

This mounting system is specifically designed to fit standard 22.2mm handlebars, providing a perfect fit every time. ...To assemble the mount, simply screw both halves together using two M5 bolts - no additional nut required due to the threaded bottom...

This is a custom-fit handlebar attachment specifically designed for Boombotix speakers, built to securely clamp onto a 31.8mm diameter bike handlebar with ease and stability.

Designed to conquer the flaws in those oversized AliExpress Bike Lights: They wobble violently when navigating rough terrain because the handlebar fails to sit below the lamp's center of gravity, and the rubber band mount simply can't withstand the...

The GPS speedometer wasn't functioning properly so I ordered a new one from Amazon that requires a specific circular opening of 52mm to fit perfectly on my bike's handlebars. To accommodate the new GPS speedometer, I designed a sturdy bracket that...

RAM mount B-size (1 inch dia) designed specifically for 28mm handlebars and secured with M4 screws. The hollow ball design accelerates printing time while enhancing overall stiffness. A strategically positioned recess within the clamp ensures a...

But I wanted it to be a bit bigger so I could mount an iPad for my kids to do piano lessons via Zoom without any issues. I decided to make it chunky because I didn't want to save some plastic and risk it being too weak to hold an expensive iPad. I...

3d printed mount for the handlebars on a Royal Enfield Interceptor 650 along with a case for a Kyocera DuraForce Pro 2 with a wireless charger, and one w/o the wireless charger with opening for the usb, and an action camera mount. The mount and...

Spare Parts Required ### For the Holder Itself: * 1x [M5 nut](https://letyshops.com/r/aliexpress-ww-07ebdc400262) * 1x [M5x35 or M5x50 (longer for wider phones) bolt](https://letyshops.com/r/aliexpress-ww-ae08eac70b51) ### For the Sample Handlebar...

I designed this wall-mounted iPad mini 2 holder specifically for use as a CCTV monitor. The structure is built with four shells, each with a 0.2 mm layer thickness and an infill percentage of 10%. To ensure secure attachment to metal surfaces, I...

This is a mounting system designed for your iPad Pro, perfect for enjoying comfortable viewing while lounging on those lazy days. The horizontal bars that connect the printed connectors are crafted from 0.5" square stock aluminum: two pieces at 8...

You have been warned...I didn't not find it necessary to put any supports in the circular openings (the holes the bolts fit in to), they printed just fine with PLA (and likely with PETG as well).UPDATE: added clip for iPad 7th gen - 10.2"Print...

Universal Handlebar Phone Mount | Harness SystemFor ANY Phone With/Without CasesA, REDESIGNED, simplified version of the mount I use on my motorcycle.Maximum handlebar diameter of 26mmRequired/Recommended Filaments:Flexible Filament - Harness, Phone...

This iPad mini holder is specifically engineered to pair perfectly with an OtterBox Defender case securely attached.