inventor drawing 3d models

https://youtu.be/Msw1_5msjjo This project draws inspiration from https://www.thingiverse.com/thing:2348263, but offers a simpler approach by reversing the torsion spline's orientation: Gudo & Neotko stab the spline through the printhead, while this...

When drawing the gun use the grip shown in the last picture (sort of a modified Vulcan salute) and press with your middle and ring fingers to grip the handle. This will force the holster off the gun and it should pop off assertively, leaving nothing...

Thank you to Banggood for providing me with the Ender-3 V2 3D-printer.You can buy one here: https://www.banggood.com/custlink/3v3hCfiZyI Video can be found here: https://youtu.be/IN2g572FZOo More info can be found here:...

He draw us a draft on the whiteboard, and it already looked like the finished one:  Then we went through all the remixes of OTTO and tried to find both inspiration and stl files to inspired ourselves form. Thelmo decomposed the character design an...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

... To optimize exposure, the (modest) rattling will draw attention. If the text is upside down, reverse the following order of the port numbers 3-12 in the Arduino sketch. ... https://youtu.be/rEn0A5Q5Hw8 https://www.youtube.com/watch?v=9UMbsx2-I3E

Based on the bottom surface of the counterbore hole for the nut, draw the same straight line as one of the hexagonal sides of the screw hole to make an equilateral triangle.Then, rotate and copy the equilateral triangle as shown in the figure.4. Cut...

Think about how much fun it will be to level your printer (okay, maybe not that) - and press the print button, watching your plastic print monkey draw layer by layer as you drift into a deeper and deeper sense of calm...\r\n\r\nWait, no! Don't fall...

For the 84 LEDs in my version, a 2 Amp supply should be plenty to power them all at full brightness (although the WLED allows for setting a max current draw if needed). I didn't have a 5v supply that could provide enough current so I used a 12v...

So...I went back to the drawing board and redesigned the lower half to support the USB-C versions of the pro-micro. So now you have both, or either. You get to pick, that's what i'm saying. I uploaded the raw QMK firmware folder (just...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

This device has not been tested or approved by any governmental organisations. Technical drawings are on my website: https://alexanderclarke.id.au/ Twitter: @fifteenforty Resources for those interested: Design of anaesthesia breathing circuit...

These nanite-hives also have enough spare mass that they can manifest as more than simply melee weapons, using their cohesive elements to create pneumatic rifles that draw off their mass (starting with jewelry, earrings, etc. and other non-critical...

Here is a concept drawing, machined from two pieces with barbed fittings embedded (these could also be female thread to accept nylon fittings). Stanley A Meyer WFC Single Cell Flow Through design can be used for nano bubble water air or mist etc...

Both current draw and the body diodes used as freewheeling diodes are used out of spec, your mileage may vary. Elements that work well: -printed axles with printed "c-clips" work pretty good, using the 1.5mm drill bit on the bearing holes to...

In the corner of each technical drawing, there are the slicer settings I recommend for each of the parts.Gimbal adapter with rubber dampersThis is the part that attaches the gimbal to the locking element which is then used to attach the whole thing...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

______________________________________________________________________ Links: Wikipeda Entry ISO7010: https://en.wikipedia.org/wiki/ISO_7010 Colors for safety signs https://en.wikipedia.org/wiki/ISO_3864 Wikimedia source of .svg:...

My primary goal was to achieve a slight negative pressure within the case, sufficient to draw in fumes and particles but low enough to prevent temperature fluctuations. The attached files include the sleeve and bottom flange, the cartridge for the...

I added a button for manual activation but mainly used it during the testing phase, and I'd maybe keep it for occasional bugs where the device doesn't perform exactly as expected.\r\n\r\n**One important thing to note is that the servo will draw quite...

In fact the raft lines may even draw over the edge (Cura) if its not centered but since they are not connected it doesn't hurt anything. Its made to print on its back and not need any support. You will notice i switched to Prusa because Cura...

I chose parallel, which will put a higher amp draw on the board. I didn't check specs, so do this at your own risk, but it's running fine so far! No support necessary for anything. I printed in carbon fiber infused polycarbonate, but PETG should...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 48 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

So, despite my obvious lack of talent, I was obliged set about drawing up my own. It's inspired by Rocco's original, but is a complete new ground-up design. I started from the circuit board specs on the BIQU page to get the fixing holes in the right...

http://www.thingiverse.com/apps/customizer/run?thing_id=184196 Instructions Using the following options: image_file = arbisign_v120140724-10430-h4kj76-0.dat outline = diamond my_image_height = 200 my_scale = 100 use_drawing = no my_y = 0 my_x = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Chemistry modelling sets can help us visualize molecules in meaningful ways.This kit is designed with 3D printing in mind and to be displayed on a flat surface, much like we draw molecules on paper. By inserting small magnets, you can also attach...