inventor cad drawings 3d models

Make the outer two pentagons marked for construction.  b: Make pentagon two 50 cm and the outside pentagon 100cm (you can scale it at the end)c: Draw a line from a point on pentagon one to the corresponding point on pentagon two.d: Make the length of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 34 printer_tolerance = 0.4...

This light draws 0.15A at 120V, 0.075A at 240V, 0.065A at 277V, 1.5A at 12V, or 0.75A at 24V.Versatility: The LEDBLT-18W is listed for use in United States and Canada. The unit carries an IP65 waterproof rating ensuring protection against ingress...

A full installation using 19 strip segments will draw approximately 1.14A at 12 volts. For side and top rails, solder on a pigtail at least 8" long, this makes routing the wires around the Z rods easier. For the top rail, if you run the wiring on...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I make no promises that it will be sized right for any 5-pack of 1¼" fuses, but my suspicion is because the Eaton Bussmann fuse pack has been around for so long (there are lots of people on eBay and other aftermarket marketplaces selling empty packs)...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

+ With a current draw of 20 mA, you'll need to drop about 10V from the power adapter in order to power the LED. That means you need about 500 ohms of resistance. I used 3 x 330ohm resistors (2 in parallel in series with another 330, ends up at 490...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

In the sectional drawing, the left port is the reservoir, the center top port is the output, and the right port is the switched filling port. Here's a video of the assembly: https://youtu.be/_z327hESdH4 Before the cycle starts, the piston is in an...

The smaller box that draws the tissue from the bottom should "snap" into place as it moves past small "grips/guides" while pushing it down into the slot. There are "rails" on the back so larger box fits snug so that when you pull a tissue, the box is...

It sims to over 1400' on an F32 so I might want to try that.I've made some attempts to make this as scale as I can, doing math against a 3 side drawing I found online and the diameter of a Pringles can. This is 1/24 scale, near as I can tell. All...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

washer M4 x 9mm x 0.8mm * 1 set cover plates (see PDF or DWG) * 2 holes 4.5mm on left rear frame, as per attached drawing. For the filament guide: * 1 filamentfuehrung.stl * 1 rod approximately 8-9mm diameter and L=308mm long. * 2 cap screws...

Even so, the Carrey drawings show the representations on many of the missing sections and have enabled us to locate a number of existing fragments. The original length of the frieze along the south side was 58.70 m. It was composed of forty-seven...

... to the text. Attached here are the rev 5 files. I've also started playing with some dual extrusion prints of this, so far so good! If you find you have further design questions, please reference the attached technical specification drawing.

 PETG is more flexible, and the lock needs that flexibility to work properly.Above is a drawing of the lock. It goes in the bottom of the outside tube. You insert it during the printing of the outside tube by pausing the print at 13 mm, insert the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

According to the specs, the DIP package can dissipate near 3W, which means it's possible to draw constantly up to 1A. This chip also has thermal protection and current limiting functions. Current Limiting I added an option to use the current...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Then I would draw circle shapes in the eye and delete them. Lastly I did a last check to see that the design wasn't missing any parts or the shapes etched into the model are not too drastic, but just enough to be noticeable once it is printed. ...So to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

 Controller box with house the D1 mini and run the power cords through with option for a switch.6 - 2mm Glass -  https://www.homedepot.com/p/12-in-x-36-in-x-090-in-Clear-Glass-91236/202091044 (cut 3 from one sheet)Mirror Film  -...