intex pool parts 3d models

part is exposed to chlorine-rich water from a swimming pool, hence an appropriate material should be used, possibly ABS?

About Inflatable Pool Intex, to create movement in water. Nozzle at 45°, with fixing groove. Nozzle at 45°, with fixing groove. For information after use, a 90° nozzle allows much better mixing of pool water, which goes into a circular whirlpool,...

I wanted to build an adapter that would do the opposite of this thing:http://www.thingiverse.com/thing:446404\nI have a smaller Intex pool (with 1 1/4" tubing) and I was determined to use a larger pump (with 1 1/2" tubing). The adapter above didn't...

I have a smaller Intex pool (with 1 1/4" tubing) and wanted to use a larger pump (with 1 1/2" tubing). I could have purchased something like this: https://www.amazon.com/INTEX-Adapters-Pumps-Saltwater-System/dp/B000RSICZU/ But this thing is most of...

Intex connectors for various Gardena connections with thread or quick connector

I wanted to make an adapter to do the opposite of this thing: http://www.thingiverse.com/thing:446404 I have a smaller Intex pool (with 1 1/4" tubing) and wanted to use a larger pump (with 1 1/2" tubing). The adapter above didn't need much in the way...

This is a remix that will fit an Intex 29055 telescopic rod and 32mm hose Printed with PETG, but PLA will also work (tested).

... that fit big Intex hoses, you need this union connector. ... Intex hose sizes: 32mm (1.25in) in diameter Union connector size: 65mm (2.55in) in diameter Print this design using PETG or ABS plastic. ... If you like it, please support the creator!

with this nozzle you get circular flow in the pool instead of just straight in. ...It helps to keep the pool clean.

I created a simple male to male connector for 32mm (1.25") to 32mm (1.25") hoses, extending my backwash/drain hose for my Intex 2100gph sand filter pump using existing hoses. I also printed the 38mm (1.50") to 32mm (1.25") adapter from a thingiverse...

A simple adapter to connect two 32mm / 1.25" pool hoses.That's it that's all..

You're really enjoying that pool! ...It's looking like a fantastic spot to relax and have some fun.

... the pressure of the ice. ... So here is the cover tightening ring for a 3KW electric heater from INTEX and give a second life to this small equipment very useful in mid-season. ... Caution: do not put printing media to keep nets clean when printing.

I printed this in ABS with 20% infill. ...Fits tightly in my Intex 300x200x75 Pool as an Outlet.

Connect a 1.25" hose directly to an Intex Chlorine Generator. This setup suits a 32mm or 1.25" hose, a correction from the initially mentioned 31mm size. You might wonder why another 32mm option is necessary. The reason lies in its improved print...

The connector must be attached (without glue ...) to one end of the vacuum hose. ...When you want to use your vacuum cleaner, just plug the connector on the pipe that goes to the pool filter.

To connect the vacuum hose, attach the connector firmly to one end without using any adhesive. ...Once you're ready to vacuum, simply plug the connector into the pipe leading directly to the pool filter.

Applying several coats of clear acrylic sealer to the exterior and interior of the part seals any wall holes. A generous amount of Teflon Tape on the threads seals it nicely. Print the gasket using TPU with 35% Concentric infill. The o-ring.stl file...

This is for a Polygroup Summer Waves 10ft pool with skimmer SFS400/SFS350 pump.This will allow you to remove the pump assembly and install a upgraded pump and 1.5" hose. Version #1 uses the same 3.5mm thick 24.5mm inner diameter intake o-ring and...

I'm fed up with the fact that the pool skimmer disengages from the pool when there is movement in the water and turns the vacuum pump on. Here's a support fix for the rectangular tube to keep the skimmer in place during turbulent water conditions...

This adapter makes it possible to fit a smaller conical plug into the larger Intex air ring hole, allowing you to fill up the ring with an air compressor. If you have a different size plug or blowgun tip, you can use the customizer function to modify...

This adapter allows a smaller conical plug (in this case, a cheap Harbor Freight blowgun) to fit inside the larger Intex air ring hole so that you can use an air compressor to fill up the ring. If you have a different size plug to fill or a different...

Compact item in version 2, very practical for placing our glasses while we're in our pool. ...We recommend printing it with ABS material.

We need a compact item that's really handy for placing our glasses when we're lounging by the pool. ...Printing it with ABS is my top recommendation.

... having trouble finding the right fittings for this https://de.aliexpress.com/item/4000392320402.html item on AliExpress, and it's causing a big issue. ...The fittings I received don't match up with my 32mm pool hose at all, which is really frustrating.

This enables kids just to pop the hose on and off inside the pool to stop and start it.....you can also run the pump straight to it, though you'd need to plug the hole on return with a pool bung...I haven't printed the one in the link, so I can't...

This nozzle is designed for pools with a metal frame (fi60mm). Since it is designed to be in the sun, it is recommended to use ABS material for printing. The infill density should be minimum 40%. The nozzle fits on 32mm tube. I have attached *...

I wanted to use a funtain on the out of my pump, and also be able to use a pool broom on the intake. So i remix the elbows to fit 32mm nozzle. It's a complete remake of the piece. The "in" is the short one, and the "out" the long one. It's not...

This nozzle is designed for pools with a metal frame (fi60mm). Since it is designed to be in the sun, it is recommended to use ABS material for printing. The infill density should be as much as 40%. The nozzle fits on 32mm tube. I have...

Small well be convenient to drop off our glasses when we are in our pool. I advise to print in ABS. Petit objet bien pratique pour déposer nos verres lorsque nous sommes dans notre piscine. ...Je conseille d'imprimer en ABS.