intel nuc rackmount 3d models

This is a replacement base for Intel NUC mini PC, engineered to securely hold the hard disk and onboard controller of the system, as well as accommodate an additional Syba Realtek Gigabit Ethernet Mini PCIe card. A full set of cables and an RJ45...

I wanted to lower the fan noise of my intel NUC and had a Noctua NF-A9x14 PWM lying around. I thought obout replacing the top lid of the NUC by this one and mounting the NF-A9x14 to my lid. I hoped to be able to disable (/remove) the internal noisy...

I used jbolonski's Mac Mini Monitor Bracket (http://www.thingiverse.com/thing:343588) to start, and added slots for the Intel NUC to slide into place. After a couple prototypes, this is it :) I recommend printing the top brackets as is. ...It takes a...

To enhance the setup, I added slots allowing the Intel NUC to be easily inserted. After testing a couple prototypes, we're pleased with the final product! Printing the top brackets exactly as they are is advised. Although it takes slightly longer,...

I accidentally bought an intel NUC (5i5RYK) that only takes an M.2 SSD to use as my mini home server. To squeeze a 2.5" HDD I designed this extension. You'll need : SST-CP12 cable - bought one for £6 on amazon 4x M2.5 12mm male/female...

I was looking for a mount to secure my Intel NUC on my dual monitor stand, and I finally found one. However, it had the wrong shaft diameter, which meant I couldn't use it right away. Luckily, the STL file that came with this project is specifically...

A while back I needed a better way to mount my Intel NUC Hades Canyon computer than using hot glue and gaffers tape. So I created this nice little setup that makes use of some 3D printed parts, a few laser cuts parts (which could also be 3D...

PSU wall mount for the Intel NUC 10th gen. This is remix of the "Generic PSU Mount" but I can't find the correct ID anymore. Print Settings Printer Brand: Ultimaker Printer: S5Rafts: No Supports: NoResolution: 200 Infill: 50 Filament: 123-3D PLA...

PSU wall mount for the Intel NUC 10th gen. This is remix of the "Generic PSU Mount" but I can't find the correct ID anymore. Print Settings Printer Brand: Ultimaker Printer: S5Rafts: No Supports: NoResolution: 200 Infill: 50 Filament: 123-3D PLA...

This is a custom vertical stand for Intel's NUC 8 series devices, such as the nuc8i7hvk. A quick solution to allow this device to sit upright on my desk and take up even less space. The stand has a very slight rearward tilt. Maybe this setup will...

It push fits onto the top of the monitor stand and uses the NUC mounting screws to attach the computer. Full height/orientation adjustment of the monitor is retained. It can simply be lifted off the monitor stand if needed as required. ... ...

This will significantly decrease printing time without really affecting the rigidity of the model.It doesnt decrease the airflow to the Nuc. Install it and forget it! Will fit other Nuc models, both tall and short versions. ...Please check the...

I grab the STEP file directly from Intel's website: https://www.intel.com/content/www/us/en/support/articles/000006820/mini-pcs.html. Then I simplify it and convert it into STL format for use in my project. ...I delete some unused parts, but keep the...

No hardware needed.Great if you need access to your Inte nuc and have limited space. ...A gap of 46 mm between the desk and the stand makes standard keyboard fit underneath.Printing:Print “standing" as in the picture using organic support3 perimeters15%...

After printing the original and trying it out ive noticed that the antenna holes were a bit to small so I've made those bigger, added some vent holes on the bottom with some rubber feet after printing.I also added a button and a hole for the button...

... doesn't exist as an STL, so here it is. ... SVG Files are from here: https://www.intel.com/content/www/us/en/support/articles/000060164/intel-nuc/intel-nuc-kits.html But the links are broken so probably use waybackmachine if you're lookin' for 'em.

Remixed NUC7i5BN: https://www.intel.com/content/www/us/en/support/articles/000005873/intel-nuc/intel-nuc-kits.htmlhttps://www.tinkercad.com/embed/2DSmpBkE4xt

This is a Wallmount for an Intel NUC (i5BEK) and a 140 mm Fan. ...I made this to cool my NUC in the summer

Created a 0.4 mm thick Counter-Strike 2 icon mask for my Intel NUC 11 Extreme.

Customized version of https://www.thingiverse.com/thing:1393685 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1393685

88 mm hole 82 mm square mounting holes for zip ties

Kudos for the connectors and plugs!

My main goal for this extension is to provide a home for extra 2.5-inch hard drives, but it's likely suitable for other applications as well. The original case bottom plate screws are used to attach the extension to the main case. To mount the four...

Modular Rack Designed Specifically for NUC5PPYB Units - A First-Time Creation Awaiting Feedback! ... Pro Tip: To Significantly Reduce Printing Time and Material, Simply Rotate the Top and Middle Sections by 180 Degrees.

Designed specifically for use with the Intel NUC, it ensures seamless connectivity and efficient energy transfer. With its sleek design and compact size, this adapter seamlessly integrates into any workspace or home environment. ...It's an essential...

This is a custom-built wall mount specifically designed for an Intel NUC model i5BEK, paired with a robust 140mm fan to keep it running smoothly during the sweltering summer months.

Intel NUC wall mount with 80mm fan mount if you put a fan on this be sure to put some washers or a spacer behind to allow air to flow. simple print in PLA. ...no special instructions.

Modified versions to support 5th through 7th Gen Intel NUCs and if you print extensions for the slim models to support 2.5" SATA drives.I used this model for 2.5" extensions.https://www.thingiverse.com/thing:5441566

--- Other Versions --- There are also other versions of this mount: 1 TIER v2 - https://cults3d.com/en/3d-model/home/intel-nuc-under-desk-mount-1-tier 2 TIER v2 - https://cults3d.com/en/3d-model/home/intel-nuc-under-desk-mount-2-tier-v2 3 TIER v2 -...

... simple adapters to fit on the back of the Ergotron arm. They are screwed to the Intel VESA100 mounting plate using standard M4 x 5mm screws.The NUC can then be hung from the back of the Dual Arm, hiding the cabling and freeing up more desk space.