intel nuc rack mount kit 3d models

quick and dirty remix for Wyse terminal rack mount. ... to print full set: - ears - left (twice) - right (twice) - middle (twice) - tray (twice)

filament wall mount rack you need 2x 10mm steel ot plastic tube Buy me a coffee:https://ko-fi.com/jokereuc

This mounting hardware replaces the existing wall brackets on the Leifheit Wall Rack, offering a seamless swap that requires minimal adjustment to ensure a precise fit.

Wall-mounted hanger rack can hold as many as five hangers at one time, primarily engineered with sweater storage in mind.

Rack mount 1U enclosure may used for some electronic equipment. ...Used 1.5 mm sheet metal.According IEC60297 or ГОСТ 28601.1-90

This sleek rack mount shelf is designed specifically to house single board computers and microcontrollers, providing a compact yet efficient storage solution.

Rack mount 2U enclosure may used for some electronic equipment. ...Used 1.5 mm sheet metal.According IEC60297 or ГОСТ 28601.1-90

Simple wall keyring rack, holes for mounting. ...Need to flip on bottom, I used supports to ensure printed right first time. Category: Organization

I wanted a simple rack mount for my OBI202. ... The device fits snugly and well into this holder so the ports face outwards.

Rack mount 1U enclosure may used for some electronic equipment. ...Used 1.5 mm sheet metal.According IEC60297 or ГОСТ 28601.1-90

This item enables attachment of your z-troller onto a rack, as it doesn't feature pre-drilled holes, giving you flexibility in choosing any mounting option.

Mount to attach a Yakima PowderHound ski rack to a Yakima Whispbar or Yakima Flushbar. I used a little foam door seal between the bar and the mount, but you probably can just mount it directly. ... I printed with PETG.

... I extended the back of each rack for added support. With just a few standard drywall screws, they mounted solidly in place. These shelves should hold their own weight without issue - the racks will likely give out before the mounting hardware does.

This is a simple hook that I designed to hang two of my laundry racks to the side of my storage rack when they aren't in use. The hook can be mounted parallel to the side or the adapter can be used to mount it from the bottom. To use the adapter...

Users seek secure and organized mounting solutions for their Power Distribution Units (PDUs) and other equipment within server racks. To achieve this, specialized button-style mounting hardware is designed for wall attachment. ...This hardware...

Mounting my Raspberry Pi, which runs OpenHAB, to the side of my compact wall-mounted rack was a priority. ...I wanted the Z-Wave USB stick positioned for maximum signal strength and optimal reception.

Standard Planet Mount STL file available for download. ...This design serves as a standard deep mount, measuring 1.5 centimeters deeper than the standard version to accommodate optical connectors that may be obstructed by the rack door.

Designed to mount to 1U of a standard network rack. Allows you to easily use the controller to control rack fans or other devices inside of a rack or enclosure. Print face-down. No supports are required. The STC-1000 isn't very heavy, so not much...

A remix of https://www.thingiverse.com/thing:3690500 and similar to my https://www.thingiverse.com/thing:4326937 This is a 19 inch rack mount for a quantity of 22 keystone devices. The rack is divided into 2 halves for easier printing. ...Strain reliefs...

Hi, this is my take on a Rasbery PI server rack mounting case. Its designed to print without supports and fit most versions of PI. This one was deigned with the PI 3 and Le Potato in mind. The lid is a press fit and can currently on fir on the RH...

This is a 19 inch rack mount for a quantity of 22 keystone devices. The rack is divided into 2 halves for easier printing. ...Strain reliefs are provided at each keystone location.This is a remix of:https://www.thingiverse.com/thing:3690500

I have a bicycle tail light that I couldn't mount to the usual seat post or seat mount because of a tail bag, so I made this to mount under the rear rack. It uses the hardware that came with the light (Cute Eye) to mount to a seat post. ... The holes...

Needed to mount drives in my new 10'' rack server case…. ...so far it holds.</p><p>Suitable for 3.5'' SATA drives with joined power and data extension cable (hot glued into the hole).</p>

Quick and dirty ghetto Raspberry pi mount for switching racks. ...I use these for cheap nut servers for non networked APC UPS Have tested it on RPI 2/3 fits a 1ru uses 3mm screws for rpi

Did a phone mount that works for the 1"-ish hole in my Fitness Gear power rack with my iPhone (Pro Max size). ...Should work for quite a few phone models.

A cable management system consisting of a wall-mounted rack designed to organize and store various cables ranging from 5 to 10 millimeters in diameter, each equipped with distinct connectors.

Phone mount designed to securely attach to a weight rack, requires minimal effort to install but may experience excessive friction due to slight imperfections in its design, a light sanding would significantly improve overall performance and user...

This is rack mount system for Hikvision NVR Print with PETG or ABS. Simple print with supports. ... My NVR model is DS-7608NI but other are same sizes, check with producer.

Rack Mount Solution for UniFi USG: Securely Fasten Your Device Without Additional Hardware. ...The Posts Fit Seamlessly into the Pre-Drilled Holes of the USG, Ensuring a Tight and Stable Installation.

This is a rack unit wall mount system. It empowers users to efficiently secure a standard rack unit (regardless of size - 10 inches, 19 inches or any other dimension) at the height of 1U directly onto the wall. ... Print Settings Printer: DAYCOM 3DP-100...