insta360 go 2 gopro mount 3d models

This camera mount is for both Insta360 Go 2 and Caddy Peanut. If you buy this charging connector, made for Caddx Peanut, "C0PJ-HS003 Charging Connector", you can recharge camera during flight. I posted an image with the connections for recharge...

The Insta360 Go Mount fits perfectly on the Flynoceros Skoll v2, securing your action camera in place to capture every thrilling moment of your ride. With its sturdy design and easy installation process, you can focus on what matters most - exploring...

Designed to for use with the AtomRC Dolphin airplane and the Insta360 Go 2. Front mount nose: Uses four 10x2mm circular magnets. Two for connecting to the plane, 2 for helping hold the Go 2. Slide in nose: Uses two 10x2mm circular magnets for...

To install the Insta360 GO using this mount, start by keeping it vertical with the lens pointing downwards. Then, rotate the camera slightly on its vertical axis and insert it at an angle. Finally, twist it into place to secure it firmly. I...

The user recently incorporated a unique Insta360 Go attachment into an existing design, specifically the Alien Toothpick canopy found on Thingiverse at rodrigo_sclosa's page. ...This innovative addition was accomplished through successful printing...

I'm carefully attaching the Insta360 Go camera to my iFlight CineBee drone using a sturdy Nylon Tie wrap. ...The material of choice here is high-quality TPU, known for its flexibility and durability.

Insta360 GO 2Selfie stick adapter Using Original accessory "Easy Clip" You need a 1/4" threaded heat-set insert

This is to mount a insta360 Go2 to the the V1 Acrobrat. Inspired by https://www.thingiverse.com/thing:4546716. and holds the https://www.thingiverse.com/thing:4902376 cases. ... This is meant to be printed in TPU with supports

A protective mount for Insta360 which prevents the camera from ejecting and keeps the propellers out of view. ...It is also symmetrical so you can insert the camera both ways.

This is a minimalistic insta360-GO camera mount for the Diatone Q33 tiny RC cars. It is a combination of minimicroFPV's design (https://www.thingiverse.com/thing:4317063) and Diatone's 3D file. I printed it in TPU and screwed it onto the canopy of...

Hi this is a insta360 go3 vertical mount, its compatible with gopro mounts. ... Remixed from https://www.thingiverse.com/thing:6103789

This is a remix from Diatone Tina Whoop and the Insta360 holder. ...Its not perfect but it works.

This is a Camera mount for the Insta260 GO for the Iflight Chimera 4 micro long range quadcopter. Print in TPU at 70% infill. Supports are needed. Check out my review video on YouTube. Link in bio. ...

Mount your Insta 360 Go camera securely onto a Beta 85 frame using its innovative lock-and-go system, which eliminates the need for any additional fasteners or adjustments. ...Simply snap the camera into place, and you're ready to capture stunning...

The file for NameLessRC Sunny module+ GoPro Hero6/7 lite is here: https://www.thingiverse.com/thing:4550833

Insta 360 Go with new [Twist-Lock V2](https://www.thingiverse.com/thing:3939555) mount available for download. Open Source design allows users to modify parameters, including plate thickness, lock thickness and angle. Download the Fusion360 file...

... grass). TPU printed at a layer height of 0.2mm with 20% infill, scaled up by +1-2% for a snug fit around the camera mount, which was quite tight even at the lowest scale setting. ...Scaling above +1% became impossible due to the design's geometry.

A fantastic mount for Tina Whoop by Diatone stands at 8 degrees.

Insta365 mount for Emax Hawk Pro This is a remix of https://www.thingiverse.com/thing:4675221

Here's an Insta360go mount for the Scx24 C-10 Chevy truck. It fits on the fake little light bar that comes with it. uses the same holes that it comes with so you don't need to make new ones. It also uses the same hardware the "lights" use. ...its very...

I made the source mount by AndyABG in TPU and it fits great but found that in a crash, the rear part of the mount that grabs the 2fiddy top plate would come loose and the camera would rotate forward and down in front of the fpv cam. This put it in...

I needed a little bit more secure mount for my GO 2 when racing. I based it around fin from 533 design from Thingi. Its thick at the front and the idea is to print 30-35 infill. its not loose so it wont jump out. Has hole for light...

Soporte vertical para camara Insta 360 GO 2 con 4 patas para ala RC Mini Drak Requiere 4 varillas de carbono macizo de 3mm.

This mount enables you to position your Gopro practically anywhere and swiftly detach when you're done. You only need to create 1/4 inch wide straps equipped with adjustable fasteners that can be secured to desired tightness. Design Video:...

A mount for GoPro 9 and Insta360 remote

Print using TPU.

Remix of https://www.thingiverse.com/thing:4342970 and https://www.thingiverse.com/thing:4939022 by JFR. Apply their same recommendations for printing. I'll update the thing as soon as I can and post pictures of it, even a video. ...

Please let me know how this works for you. I'm happy with it but there's always a chance I missed an opportunity for improvement. Enjoy! UPDATE: I added the camera holder .stl file from the picutres. I printed it with them standing up on their...

I made this. A zip tie and the rubber bands that come with the Nanohawk X make this work. Feel free to remix. ... https://a360.co/3mkna4u

GoPro and Insta360 remote mount holder for a 4 claw grid system.