inmotion v12 seat 3d models

The last time I made my own 3d model of the v12 seat it was quite hard with tpu 95a 0.4mm nozzle 2 wall and 10% gyroide infill so I would guess 3-5% infill could be good. *support needed* Share your make please it would make me very happy ! ...:) ...

... with my knees. this puts the seat about 5 inches above the stock seat. it is reasonably comfortable and a good choice if you happen to have a V12 seat on hand like i did i printed using petg at 30% infill. ...i think 20% infill would be sufficient.

This is a simple design that will protect the display on the Inmotion V12 EUC. I used double sided tape to hold it onto the shell. Printed in TPU @ 30% infill. ...No supports reqd

Inmotion V12 Bumpers & Screen Protector Bumpers with front lip to protect the front and the back of the Inmotion V12. Stick it on with double sided tape and you are good to go. I recommend going all the way to the ends with the tape so you have the...

Protect your V12 screen from impact! ... Attach with velcro or double sided tape, easy print.

After taking my unit apart to prepare for replacing my failed board, I noticed a little rust and also no caulking or protection from water ingress like i’ve seen on other v12’s at the phase/hall wires. I designed a little cap to add before I put it...

WARNING: MAY NOT BE ABLE TO BE REMOVED, THIS IS A WORK IN PROGRESS ALSO SCALE THE MODEL TO 10 PERCENT EXACTLY OR IT MIGHT NOT FIT I saw another v8 seat mount but that one needed you to print all parts requiring almost 1kg of filament. The seat mount...

This was Just a project to make seats for daughters electric unicycle, everything fits snug but far from perfect. The V8 file is slightly different from the photo, trimmed down the sides to make it fit better as the original was hitting the inner...

gyroroue pedals for inmotion v11 and v12. Replace the glassed grip by one with lugs and an enlargement raised towards the front. Provide a glue with double-sided reinforced. ...The models in the picture have been used for 1500 km without damage.

Protective bumpers to protect the pedal hangers for an Inmotion V11 or V12. They can be pressed into the detent hole underneath the pedal hangers with some double-sided 3M tape to adhere them even better. These bumpers regularly save my pedal...

Also appearing in the photos are the following other things I printed out in TPU to add a layer of protection to my wheel: - [Bumpers for EUC Inmotion v11](https://www.thingiverse.com/thing:4899874) - [Inmotion V11 EUC Shock...

Generic leather style car seat. ...Modelled with NURBS & ready for subdivision for close up hi-res results.

Similar to the one evans036 created, but a little longer, lower profile, and with rounder edges. Prints with no supports and best in flexible filament. ...I printed with Infill at 30%, but up or down a bit may work just as well.

Print in TPU, preferably with 4 or more inner walls. ...After printing, sand the bottom and adhere to the EUC using velcro for easy removal and cleaning.

... but with the sides pulled over the edges to protect the hangers a little more than the original. ...printed these from TPU. They'll fall off if you put your V12 on its side even if you have them on there with double sided tape, so keep an eye out.

Print in regular TPU For best softness print in NinjaFlex or VarioShore TPU 0.8mm or 1mm nozzle 1 wall 20% infill Print each piece separately

Printed in TPU with a 25% infill and .25 layer height. came out decent but its to short and needs to be redesigned for taller riders. ...Shortys will like it though :p

Mocked up to the measurements of an Inmotion V12 (from ground to bottom of the pedal hanger, at the highest pedal setting). Print Settings: Material: PLA Plus, PETG, or ABS Designed to be symmetrical. So no need to mirror. Just print two of...

#Background: The InMotion V12 electric unicycle (EUC), has a very nice front headlight and cool side lights. However, the rear tail light is insufficient for safety on the road with cars. The tail light I chose to remedy this oversight is the OLIGHT...

V12 engine

V12 engine block

The version in question, V12, is powered by a four-stroke engine.

The v12 car engine is designed for both high-speed performance and visual appeal, making it ideal for those who want their vehicle to be not only fast but also look impressive on the road.

A high-powered V12 engine, complete with fully operational internals, was crafted during my last year of high school while attending Butte College's DFT-2 class. ...The engine is currently undergoing 3D printing and will soon be enhanced with a twin...

This is a part to reduce wear on the EUK Inmotion V10/V10F pedal https://youtube.com/shorts/eiPYiSbVVkw?feature=share

Parking stand for Inmotion V8.

This clip integrates seamlessly into the InMotion V5F.

Protect your wheel with the inmotion v11 unicycle fender.

Bumpers for the aluminum on the Inmotion V13

This is a push button of Inmotion V8 handle with a high button.