injora servo 3d models
20072 3d models found related to injora servo.
thingiverse
This is a custom servo mount remixed to fit a Injora 4-link high clearance links. Print with infill 100% or 99 bottom layers. Also orientate so the part so printing is upside down for clean fit with diff. ... link to servo i used...
cults3d
This is a custom servo mount remixed to fit a Injora 4-link high clearance links. Print with infill 100% or 99 bottom layers. Also orientate so the part so printing is upside down for clean fit with diff. ... link to servo i used...
prusaprinters
This is a custom servo mount remixed to fit a Injora 4-link high clearance links. Print with infill 100% or 99 bottom layers. Also orientate so the part so printing is upside down for clean fit with diff. ...link to servo i used...
thingiverse
Injora portal axle differential locker servo mount for RGT EX86110. The mount is screwed on the central bridge between RX box nad ESC. ...Designed for two Tower Pro MG90S metal geared micro servos.
thingiverse
cab vents for the cab extensions on the injora comanche rc body
thingiverse
A replacement of stock mirror for injora cherokee hard body. ...Used 8-10mm M3 screw for mount
thingiverse
A small tray for holding electronics in an Injora chassis or silmilar when using the Furitek Komodo or Surpass 2204 brushless motor. ... A motor shroud is also included.
thingiverse
Simple no frills tonneau cover for the injora jeep comanche pickup body made with tinkercad. ...I made this for my R/C build so I could trim the inside of the bed to fit my trx-4 without it showing.
thingiverse
XR247_Servo_Mount_v2.stl: I'm running Redcat XR247 axles by using this servo mount attached to the axle. It also facilitates front 4-link. You'll need 3 M3x20mm screws, two for the links, 1 to screw into the top of the axle. Be careful with the...
cults3d
XR247_Servo_Mount_v2.stl: I'm running Redcat XR247 axles by using this servo mount attached to the axle. It also facilitates front 4-link. You'll need 3 M3x20mm screws, two for the links, 1 to screw into the top of the axle. Be careful with the...
thingiverse
Tag me on Instagram @hyght_rc Shock relocation mounts for the carbon scx24 Gladiator chassis made by Injora and OGRC. These mounts allow for better articulation, lower stance, and more shock mounting options while increasing chassis rigidity. Also...
thingiverse
Front light bar and tail light mount The front light bar is inspired by RCModelsandMods, but slightly lower depth, as I found my servo does not fit well with the original design. Tail light mount is double side taped on. ...
cults3d
Beadlock rings for 1.9 amazon Injora rims. ...For printing in custom colors.
thingiverse
I made a new battery tray for my Injora nylon crawler chassis. This is meant to fit the smaller 1500mah battery (~74x37mm). I also built it to mount the battery on the bottom side of the tray as pictured, but it should be able to mount either way.
cults3d
Folding replacement mirrors for Injora Cherokee. After printing apply a little pressure and mirrors will fold perfect. Very durable and easy to print. ... .28 20 Wall Layers 0 Bottom Layers 0 Top Layers 35% Support 0% Infill
cults3d
Meanwhile, Injora's potent upgrade package pumps up power and performance to previously unimaginable levels. But it's not just about raw speed - it's also about finesse and control. The Austar chassis is designed to work in perfect harmony with your...
thingiverse
Modification complète du INJORA buggy Rock crawler Batterie fixée à l'avant de la voiture et très basse pour un meilleur équilibre des masses (à imprimer en 0.8 de largeur pour une meilleure solidité). Système de capot facile à ouvrir et sans...
thingiverse
Front or rear bumper for injora lcg frame...84mm in clear for 78mm wide frame...holes start at ~5mm and have 8mm spacing to match frame and are a little loose to help ease install.. ... printed 4+ perimeters , 100% infill @.16 with petg but have had...
thingiverse
This is a magnetic body mount for the Injora crawler RC chassis. It works on both the front and rear. It is designed to work with the Amazon magnetic body mount kit linked below. ... ...
prusaprinters
Injora Jeep Cherokee XJ Hardbody mounts for the Traxxas TRX4 printed in PETGI modified the original rear mount to make sure the wheels were aligned in the wheel wells.The rear mount is a modified version of another that I found a while ago, but I...
thingiverse
These center caps allow you to use the Injora after-market rims with center caps and still be able to take the lock-nut off and on without taking the 6 center screws out. Depending your printer there's two files - 1mm and 1.25mm, which varies the...
thingiverse
I designed this skid plate in an effort to fit trailing arms to my Injora crawler chassis. In the end the chassis just wasn't wide enough to match the trailing arms and the axles (ar60) I wanted to run. I still liked the design, and it's a bit...
cults3d
Hello Here are a dozen elements to print for your Injora RC buggy that I designed on fusion 360 Several small problems with the original chassis sold a little less than 30 euros have pushed me to design these parts : Hood and roof fixed precariously...