ikea ps 2014 lampe 3d models

When it does you maybe want to just fix the joint rather than 3d printing & replacing the whole plate (using AOL06's great design) This print is the joint of any of the IKEA PS 2014's plates. It has the same curvature as the plates so you can glue...

To turn your ceiling lamp into a floor lamp, follow these simple steps: * IKEA PS 2014 lamp * IKEA RODD floor light base * A light bulb * A 3D printed adapter I used my Dimension Elite to print the adapter with a layer thickness of 0.17mm. Some...

We were pretty disappointed when we opened the box on our newly purchased Ikea PS 2014 (AKA 'DeathStar Lamp') only to discover that we'd need an electrician to install it, so we designed this adapter to enable us to connect it to our existing light...

We're offering a cover to put on the original Ikea lamp and transform it into the Death Star from Star Wars! It's designed, tested, and approved by Dagoma. ...Enjoy!

Nous vous proposons un cover à mettre sur la lampe originale d'Ikea pour la transformer en étoile de la mort de Star Wars ! ... Elle est dessinée testée et approuvée par Dagoma :) Enjoy !

The lamp and its relative base rest on the desktop, enabling it to slide smoothly to either side. ...This wall-mounted lamp requires no additional support, allowing users to position it along the full extent of the work surface.

I need to find suitable large LED light bulbs for a vintage-style IKEA PS 2014 table lamp that adds a touch of elegance and sophistication to any room.

This lamp won't work right if you don't hook it up to the ceiling using Ikea's PS2014 lamp hardware. You should know that this lamp won't stay closed on its own and its weight causes it to swing open, which is why I'm going to add a motor to control...

Hello ! ... This is an adapter for the "IKEA PS 2014", mounted on a Manfrotto 5001b tripod. ... Best regards, Jeremie.

Hello! ... I'm writing to share with you my DIY project - a custom adapter for the IKEA PS 2014 camera mount, cleverly integrated onto a sturdy Manfrotto 5001b tripod. ... Warm regards, Jeremie.

A friend of mine recently snapped one of the external skin parts off a beautiful Ikea PS2014 lamp, so I whipped up a 3D printed replacement piece - it's far from perfect but I think it'll do the job just fine.\r\n\r\nEdit 2019-01-10: A new version...

This versatile adapter is designed specifically to attach an Ikea PS 2014 light fixture to any surface featuring a standard UNC-20, one-quarter inch thread. ... Changes: The latest update, V3, has been significantly enhanced with increased depth,...

The 2014 IKEA limited edition desk is a stunning addition to various interior designs, such as small offices, sleeping rooms, and hotel spaces. It also works well in gaming environments. The package includes a highly detailed 3D model with separated...

A slightly taller adapter to fit a Philips (WiZ) smart LED A80 18.5 Watt bulb that is 16.3 cm tall.

The workstation was slightly too low to complement our ergonomic office chair, causing my preferred student to slouch over textbooks.\nWe produced two additional layers of reinforcement to elevate the working surface by approximately two inches (47.5...

... ...The specifications used in this customization include a stick width of 8, flat-bottom enabled (value of 1), hole radius of 3, message "CTC PS 2014", stick thickness of 3, font size of 10, and the "write/Letters.dxf" font with a font thickness of 5.

... in wood-PLA. I use this here as a housing:\r\n\r\nhttps://www.ikea.com/de/de/catalog/products/40386590/\r\n\r\nThe light bulb is also from Ikea:\r\n\r\nhttps://www.ikea.com/de/de/catalog/products/70338951/\r\n\r\nMy drill bit diameter is 0.6 mm.

Als Fassung verwende ich diese hier: https://www.ikea.com/de/de/catalog/products/40386590/ Die Glühbirne ist ebenfalls von Ikea: https://www.ikea.com/de/de/catalog/products/70338951/ Der Düsendurchmesser beträgt bei mir 0,6 mm. Print...

Specifically for this task at hand, attention is focused on this desk. To begin, carefully carve out a slot by removing the plastic cover using a trusty utility knife - all while being mindful of those delicate fingers! ...Once that's done, open up the...

Plastic clips for the Ikea PS Pendel clock which hold it in place. ...For maximum sturdiness, print vertically and with supports.

The IKEA PS closet-cabinet is an innovative storage solution that combines style and functionality. With its sleek design and versatile features, it can easily fit into any room and adapt to your changing needs. The cabinet offers ample space for...

IKEA enthusiast discovers game-changing technique for assembling and rearranging their beloved PS Series kitchen cabinets in an instant. By simply utilizing a versatile adapter device specifically designed for this purpose, anyone can stack and...

I purchased the IKEA PS metal "cage" cabinet and discovered there were only a few limited options (and color variations) for the decorative plates - which could not be bought separately either. ...So, I decided to create a CAD model and print some...

Picked up a lamp like the IKEA kind

EDIT 20/07/19 : USE THE V2 VERSION ! ...Hooks are much more powerful now ! Assistance for the Ikea Janjo lamp holder for an Ikea Skadis plate. ... STL and SolidWorks files included.

Pied lampe ikea   Imprimante : Prusa i3 mk3s Couche : 0.2 mm Remplissage : 100 % Petg Transparent purple de chez Prima Creator   diamètre supérieur 13mm diamètre inférieur 8mm

Halter für alle möglichen zwecke um eine IKEA Lampe oder jede andere Lampe mit Clip anzubringen Einfach mit 4 Spax schrauben festschrauben Verwendetes Material:Prusa MINI Prusament PLA Marmorgrau

Pied lampe ikea Imprimante : Prusa i3 mk3s Couche : 0.2 mm Remplissage : 100 % Petg Transparent purple de chez Prima Creator diamètre supérieur 13mm diamètre inférieur 8mm

Die Glasabdeckung der IKEA Lampe ist mit drei Klammer, die aus einem klaren, harten Kunststoff hergestellt sind, befestigt. Sie wird dort eingeklipst. Wenn die Lampe schon etwas länger hängt, brechen die Klammer schon bei der kleinsten Bewegung. Also...