ikea lack shelf unit 3d models

I needed some custom legs to loft an IKEA Lack Wall Shelf Unit up off the floor in order to clear baseboards. The leg is 2" square to match the thickness of the shelves and 4.25" tall, which was the height of our baseboard. I added two tabs on the...

Then I got a third sensor to enable full 360 degree mode, but the optimal location for this sensor was not a wall, but the top of an Ikea Expedit (not Kallax) shelving unit. So I figured I'd design this one to go with the existing two mounts - so I...

Bracket for an extra shelf on the IKEA LACK

Shelf brackets making popular Ikea Lack more stiff by implementing shelf.. I have found my Ikea Lack to be very wobbly during printing, thus before switching to Klipper and increasing accelerations I wanted to make table more robust. 1st step - leg...

Right-angled bracket for supporting IKEA Lack shelves.Bracket is designed to provide extra support to any size of the IKEA Lack shelf collection. In particular when anchored to dry wall without studs. Includes screw holes for securing to the...

A simple and sturdy shelf hook for the popular Ikea Lack floating shelf. It's not a pretty design but very functional and robust, will make a few variations of this and upload when I have time. Check my 2nd version of this out here...

I want to use a IKEA Lack shelf as a monitor and speaker stand on my desktop.. It's a bit too big for my CR-6 SE to print, so gonna make a split version also. Infil i will go for: 20-30% No support needed, just rotate the flat side against the...

I created these Lack Shelf Clamps for hanging our babies stuff directly on the shelf. They are snap on, print without support and brim. I used the longer version for hanging babyclothes, you can hang anything else there of course as long as it...

The idea is to cut the Ikea Lack shelf to reduce the depth (originally 26cm). When you cut the shelf, you remove the parts to fix it on the wall. The brackets here allow to fix the shelf on the wall with glue. ...

... side without the white finiture… I put this side on the rear! Thingiverse doesn.t accept upload for my photo: have a look at this project in my account on printables. https://www.printables.com/it/model/292394-ikea-lack-enclosure-shelf-support

Headset holder for an Ikea Lack shelf. Designed for Steelseries Arctis 9 & Arctis Pro but will fit most headsets.Attention: I have several Lack shelf´s and noticed that they are sadly not consistent in thickness. This holder will fit if your...

The Ikea Lack shelf corner protector for children. We use shelf as low as one meter above the floor and it represents great danger of child damaging himself as he jumps around the appartment. Therefore, some stylish corner protection in Lack design...

The Ikea Lack shelf corner protector for children. We use shelf as low as one meter above the floor and it represents great danger of child damaging himself as he jumps around the appartment. Therefore, some stylish corner protection in Lack design...

I added a 3rd Lack table under the enclosure makig it taller and also put wheels.Whe long legs are simply original ones screwed together with original ikea double-screw.Put 2 very long screw from under the lower table for keeping in place the...

This is for Ikea Lack Shelf which thickness is 50mm. This one has the optimum dimensions among i made ever. ...Print Settings Printer: Sunhokey Prusa i3 ...

A headphones holder for the Ikea Lack shelf. The cable clips are for a 4mm cable, which is the one that uses my DT 770 PRO. I also include the M, the first letter of my nickname. ... It took 1h 45min to print on my Ender 3 Pro, with supports.

Simple LACK shelf cable management that uses a 27mm wide velcro strap to hold cables.

I was trying to hang some floating Lack shelves from Ikea and was failing miserably. Lathe and plaster walls combined with impossible-to-see-when-mounting shelf mounts designed by Goldilocks (screws heads and spacing have to be JUST RIGHT) was...

A headphones holder for the Ikea Lack shelf.The cable clips are for a 4mm cable, which is the one that uses my DT 770 PRO.I also include the M, the first letter of my nickname.It took 1h 45min to print on my Ender 3 Pro, with supports.Print...

... ...Added a half sized version for smaller items. Check my 1st version of this out here http://www.thingiverse.com/thing:1129058 The lack shelf is 50mm thick as standard, I made this dimension on the bracket 50.5mm to allow for any tolerance issues.

Hey Folks, I did this thing, originally to hold my jansjo lamp on the lack shelf. But then I modified the design a bit, so now there are some hangers for those shelves as well. I didn't try the hangers yet, so I have no idea, how much weight they can...

This Unit helps you to stack the IKEA Lack tables to a Tower. ... With the screws, this Unit makes the Tower more rigid.

add a 25mm rod mount below ikea LACK Wall shelf

Good headphones holder for LACK shelf from IKEA. ...Easy mount.

This is a simple GoPro mount for clamping it to the IKEA Lack shelf (50mm).

Info: https://www.ikea.com/de/de/p/lack-wandregal-weiss-90282180/ https://www.ikea.com/gb/en/p/lack-wall-shelf-white-90282180/ https://www.ikea.com/de/de/p/lack-wandregal-weiss-50282177/ https://www.ikea.com/gb/en/p/lack-wall-shelf-white-50282177/...

Info: https://www.ikea.com/de/de/p/lack-wandregal-weiss-90282180/ https://www.ikea.com/gb/en/p/lack-wall-shelf-white-90282180/ https://www.ikea.com/de/de/p/lack-wandregal-weiss-50282177/ https://www.ikea.com/gb/en/p/lack-wall-shelf-white-50282177/...

This is a simple camera mount for the IKEA Lack shelf. ... The rubber "door buffer" (8.5mm diameter) are optional.

A simple filament holder thats fits an Ikea "Lack" wall shelf. Works with any 5cm thick shelf. ... XL is for two spools (1 small and 1 large)

Fixed the width of the original, as it was 1 mm too wide. ...Now it fits tight to my IKEA Lack shelf, which is exactly 50 mm wide.