iflight ix2 3d models

One is a wide Martian or Alien frame the other a narrow iflight titan 5" frame. With same hole distances also found on other types of frames the one or other mount may also fit to your frame. Large holes save weight and printing time and let you...

... antenna in. The mount is a friction-fit based design for frame standoffs with a diameter of 6 mm. The distance between the center of the standoff holes is 22 mm. Works on most of the Iflight Frames. ... Feel free to use or remix this design.

## Xilo Phreakstyle Front Chin/Camera Protection Inspired by the front "chins" of the iFlight Nazgul, I also wanted one for the Xilo Phreakstyle, after a crash which destroyed my FPV camera. Two versions are available: - Simple Lightweight Chin -...

I have a iflight cidora sl5 frame, and whanted a mount for my TBS unify. I wanted to fit it in the rear of the drone because i have a 30.5 mm mounting pattern back there. But due to the capacitor i needed a cutout in the mountingpad so it would fit.

My configuration: * Motor: HGLRC 1407 3600kv * Power source: High-capacity 4S Lipo battery delivering 650mA of power * Flight controller: iFlight SucceX F4 V1 Mini, utilizing the advanced Blheli_32 ESC technology and capable of handling up to 35A of...

... this balance lead adapter and just utilize the usb c part. Doing it this way eliminates the need for connecting/disconnecting the battery every flight. https://pyrodrone.com/products/iflight-type-c-to-balance-head-charging-cable-for-gopro-hero-6-7-8

- base plate for the Matek F405-WING FC - holder for a R9MM and buzzer that fits on the FC base plate - ring reinforcement for the FPV camera - case for a BN-220 GPS - AIO FPV holder (camera, VTX and antenna) Parts that I have used: - Matek...

Arm guards for the iFlight Nazgul or Cidora. Can be oriented for soft mounting or hard mounting the motors; works both ways as shown in the pictures. I printed the guards in TPU, but printed the Print Supports in PLA. Pause the print before...

Main frame parts i prinded with "filamentarno aerotex" filament with carbon fiber, prop guards : PLA, landing gears (needed only with top placed battery): PETG, Camera mount: PLA Columns: 3x 25mm aluminum columns for m3 My rig Flight controller:...

I designed this adapter for use with the GoPro mount provided by the iFlight manufacturer, I only replaced the 2 mounting screws with longer ones to attach the XT60 adapter from the bottom. ... Print in hard TPU (i use 40D), 100% infill, no supports,...

Some Specification: Wing Span: 1200mm Length: 760mm Take of Weight: 830g Wing area: 17.5 dm2 Wing loading: 47.4 g/dm2 WCL: 11.3 Parts use: Motor: 2806.5 1300KV Iflight motor: https://sea.banggood.com/custlink/mGKdw3rkoe Emax motor:...

So I designed this to sucurely mount 2 antenna's for the RX and an iFlight 60mm omni. Should also work for a Caddx Nebula antenna. If you plan on converting to HD. The slot in the side takes a 1.9 mm zip tie, to secure the VTX antenna. So... No...

Material: Electronic components include the Storm32 V1.3 in NT mode from Banggood and brushless motors GBM3508-130 from Drotek, also available at iFlight-rc. Additional material includes a LIPO Battery 3S 2200 mAh. The StorM32 NT IMU Module v2.0...

Has sufficient space for an internal iflight bec, uses the buttons (AND ONLY THE BUTTONS) from betafpv for the gopro 5,6,7 and more importantly lets you use the stock lense mounting system. It uses the original front face of the gopro 5,6, and 7...

... Occasionally, I use hot glue to keep my antennas in place, but the iFlight bottom plate features two protrusions that work incredibly well as an alternative attachment method. This makes it easy for me to secure my antennas without relying on glue.

### VTX Antenna mount TPU/Flex - it fits my iFlight XL7 - it fits my Apex Clone ### Intention: - Lightweight TPU Mount for for 30mm tall standoffs, 27mm apart at standoff center. ### Observations of the current model: - Maybe need tighter on...

This frame in action = https://www.instagram.com/p/BxIZupLHMsi/ Weight = Frame & Electronics (no batt) = 59.1grams Build specs: Motors = AMAXinno 1103 7500kv (both 3 hole and 4 hole motor mounts) FC/ESC's = iFlight SucceX FC/ESC 16x16 Stack (I did...

This is two parts: 1: mount with 4 screw holes for the DJI O3 main unit 2: mount for included DJI video antenna I modeled this on a iFlight Nazgul5 V3, but the measurements and bolts are as follows: Main DJI O3 mount: 30x30mm screw spacing, intended...

This is the completely fresh designed RX antenna with my Iflight Titan Beitian 220 GPS mount. With this you should be able to print this without support with TPU 95a. A picture follow as soon the print is finished and build into the Transtec...

... tape. May not fit depending on how your drone came from iFlight, but I did give it a bit of room inside to account for some variance. ...Let me know if you need this slightly modified though, and I should be able to make a custom version for you.

Tested on 3 different 5 inch frames : TBS Source One v4, iFlight Nazgul v1, Team Mistral AK47 A lot more information as well as the 3D models available here : https://github.com/Mixyfpv/mixys_quick_ducts Additional hardware required (per duct) : 1 x...

So I opted for the iFlight XL7 mount instead and adjusted its mounting holes to fit perfectly on the HD1 frame. The print came out great when done sideways. If you're prone to crashes, consider adding a zip tie or another reinforcement to secure it...

Gopro8 mount 16° titl for Iflight bumblebee The design includes full access to battery, buttons and as much as possible to back screen. The design is based on 6mm hollow bumper all arround the gopro, and more thick around the lens in order to...

The canopy is shown paired with an iFlight Succex F4 12A AIO board featuring a stacked VTX unit, FrSky R-XSR transmitter, Runcam Nano 2 camera, BARD 1103 8000kV motors, and HQProp 65mm propellers. I have also designed a battery mount that can...

I designed this Mount in Tinkercad for my quad, it fits perfectly on the iFlight Cidora SL5 5 Inch frame but might work with otheres as well. The dimensions of the holes are 36mm x 25mm and Its tilted at 30 degrees. Mounting this to the drone is...

The provided STL files offer compatibility with GoPro 3 cameras using iFlights motors. Printing requires support for the arm; Kiss slicer is recommended. Key modifications include adaptations for GBM 2208/2212 iPower motors and enhancements for...

Luckily, I had some spare dampeners that came with my DYS F4 flight controller, but you can opt for similar ones: https://www.amazon.com/iFlight-Vibration-Rubber-Controller-Absorption/dp/B071RP443J Here's a link to the X Class build details that I'm...

... and maximizes the chance for a better radio/video connection. The GPS TPU mount is specifically designed for the GOKU GM10 Nano V3 GPS and the LED/Buzzer mounting holes were designed for the iFlight 2pcs 5V Buzzer/LED. ...(Both pictured above)

https://www.cncdrones.com/saf-4-inch.html Designed to fit o3 and 20x20 ESC/FC, with 23mm standoff height to make room for kiss/fettec Props outta view in 2.7k100p 4:3, ive found 4s 850-1200mah to be about the right weight - Carbon 1 - topplate in 2mm...

Because I wanted to use the rapidfire on my DJI drone and I didn't want to use the $20 Iflight module when I had everything I needed at home. I modified a design found on Thingiverse to look like this. I suggest you use a 5v BEC. There are two files,...