iec 320 c14 inlet 3d models

This is a removable screen cover for a 4" combustion air inlet (e.g., furnace, water heater, etc.). I found that the metal fitting inside frosted over too much in cold weather, and I hope I can leave this one on year-round (I'll update this after the...

UPDATE Added new .stl File.Based on my 45° air inlet i changed the geometry:The air intake is now extended and shows about 45° upwards.With this design (many thanks to user chewey for the idea! ) there should be less hot air form the bed sucked...

... bit loose, but it should hold its position. We plan to refine this design further, but initially, it performed well and minimized mess. If there's sufficient interest, we'll create various sizes of inlets and slightly taper them for added security.

This is a 4-inch inlet shoe that's compatible with the Suckit dust shoe mounting brackets for the SO3 with the HDZ upgraded Z-axis. The light blue is a 2.5-inch Suckit dust boot I purchased, while the black is a 4-inch dust boot I designed myself.

The design I made is really only covering the inlet itself, and therefore does not interfere with any wires or other parts of the printer and it also allows it to still move in all directions just as it can without the cover being attached. The cover...

Parts needed: 4 - PC case fan screws 1 - M3 x 10mm dowel Installation: Drill a 1" hole on your enclosure where you would like the air inlet to be. One of the parts to print has a tube with 4 mounting holes. Slide the tube into the freshly drilled...

This part will allow you to connect an Intex Vacuum ZX300 over pressure valve to a standard 50mm male threaded inlet or return (like mine from Olympic (...

Hi Because I have a mounting for the teflon tubes on my i3mk3 MMU 2 I made a wall bracket for my Prusa MINI teflon tube. MMU2 Version here You need: Printed parts ;-) 2x screws M3,0x12 and Nuts longer teflon tube ( I was satisfied with the piece I...

After shutting off the main shut-off valve and the electric power, I removed the cover to find a clip had snapped - the clip that holds the water inlet filter assembly in place. Without it, water was spraying everywhere. So, my 3D printer at the...

My good friend Tim asked me to help him develop a paddle holder for his new Oru Inlet Origami Kayak. The paddle holder was tested in PLA and was plenty strong for the task. The paddle/oar end of the holder pressure fits around the pole of the...

Naca Inlet - 12 inch Also excel sheet to calculate different inlet sizes to match your size needs

This is a 4" inlet shoe that is compatible with the suckit dust shoe mounting brackets for the SO3 with the HDZ upgraded Z-axis.The light blue is the 2.5in Suckit dust boot that I bought. The black is the 4in dust boot I designed.</p><p>Here's the...

It's compatible with old-style German inlets from the 1950s and 1960s, but make sure they're not too tight. For older-style German inlets, check out my other listings for a suitable plug. ...This plug was designed using Tinkercad and can be edited...

Electronics 1x Bigtreetech SKR 1.3 mainboard 4x TMC 2208 Stepper driver 1x BTT TFT24 or BTT Mini12864 display 1x Mean Well LRS-150-12 Power supply 1x SSR Relay 8A - Hoymk SSR-D3808HK 1x 16mm anti-vandal power momentary switch - 110/220V variant 1x...

IEC320 C14 Electrical AC Power Socket 3 pin red LED 250V Rocker Switch 10A fuse male inlet connector (model AC-17)Available on Aliexpress: https://www.aliexpress.com/item/4000401609168.html

For socket such as...

uses a very special and hard to get power inlet connector, here is how i solved it, by adding a standard IEC power connector, ok it dont handle the full potential 20A nor 3phase input option, but who need that anyways ?? see the pictures and you...

This is a housing to mount a Corcom(TE) PM series Power inlet on the Voron 0.1

Airbus 320 Neo Jet compressor

... my camera and DJI Mavic Pro drone power supplies when traveling. For further information on this type of coupler, visit https://en.wikipedia.org/wiki/IEC_60320#C7.2FC8_coupler. ...So far, the cover has fit all the supplies and chargers I've tested.

This model was crafted using Tinkercad's intuitive tools. ...Make your edits directly on the site at https://www.tinkercad.com/things/lVduy0BEPjd.

I'm gearing up for high-speed runs where a reduced center of gravity takes precedence over travel. To achieve this, I'll install the bushing below the screw head in the suspension, effectively lowering it by 7 mm. Since this model is straightforward,...

This is a 3 part model. The supports braces have a contour on the bottom that matches the roof of the truck, so print them upside down, and print the roof rack flat on the bed (the files are already laid out correctly). See print settings for best...

Here is an electronics tray I designed for my WPL C24 Toyota Hilux rockcrawler. It is designed to be able to use the stock rtr electronics or to provide extra room for aftermarket. The version with shocktowers are for custom shocks that I built. You...

I used this file on my printer enclosure build. ...The wires in the PSU cover were thight so i made a separate bracket for the power plug.

For precise dimensioned mounting, the simulation is accurate.

This 3-part model features supports with a curved bottom contour mirroring the roof of the vehicle, necessitating upside-down printing, while the roof rack should be printed flat on the bed, as the files are already optimized for this setup. Consult...

A clever trick for your Arduino DIY project has evolved to utilize an inlet power source. You can discreetly hide a USB power adapter inside a cooling box! This feature is part of my IoT MySensor based SmartHome project, which relies on open-source...

Acoustic system Sven MS 320. ...Two-way speakers and subwoofer.

MEAN WELL RSP-320-24 holder for Bear upgrade.