ideas cad 3d models

For the ones included, the idea is to mount the body to the bumper mount cross members. I like that solution because they are nice and inconspicuous but it means that my generic bumper mounts no longer work so I have been grappling with that...

I already have a few ideas floating around for completely different wagon types using the same parts to some extent. I'm also currently studying to be a mechanical engineer so that comes with its perks too i guess, mostly in the shape of Siemens NX...

Also, do feel free to drop me a message, if you have problems with printing these or if you have ideas for add-ons or for how to improve the designs.All my models are free and may be used and shared by everyone. I put a lot of time in my designs to...

General ideaPlacing a 40x40x4 concrete slab under your 3D-printer significantly reduces noise/vibration transferred to the enclosure.Placing the slab on top of the LACK table causes reduced height needed for the printer PRUSA MK3S+ with MMU2S.In this...

When Thanos suggested killing half the population of the planet to solve the problem, his idea was considered too drastic and was dismissed by his people, which resulted in Titan becoming subsequently devastated as well as nearly uninhabitable. One...

:) Modification IdeasPlace a battery or a small power bank inside the base and convert it into a portable fanUse an Arduino or a Raspberry Pi to control the fan Updates2020-08-20 Updated the list of materials. Print instructionsG-code...

To do this only connect one of the colored wires going into the driver and combine the two colored wires from the lamp to the one colored wire on the lamp.The high level process is:Check the length of the COB Led against the mount and cut it where...

Kaptan tape is optional but a good idea. A small wire connecting the cells is fine, they will see a max of 1A charge and 250ma discharge (collectively). Check youtube for tutorials on soldering to batteries--a light sanding, solder flux,...

If this isn't desired, adding additional solid objects, or simply sinking the objects .3mm on the build plate in the slicer will skip this with no problem.Besides material changes on the first few layers to give an outline effect, I tend to insert a...

But make sure not to cross cables/connections.Step 11 It would be a good idea now to connect all the stuff provisionally and test it.  Oh shoot! We've cut the power cable. Damn it! Call your therapist (again) immediately.No problem. Use Wago...

Probably a good idea to print a couple of the mounts. It's easy to screw it up when adding the brass inserts. You'll want a piece of PTFE tubing between your extruder and the radiator. Measure the depth of your radiator, and the depth of your...

If you have printed either of these designs and would like to share your feedback or ideas for improvement, I would love to hear it. ------------------------------------------------------------------------------------------------- Version 2.0...

This covers an old version of the board but still gives you a good idea of what is going on. https://www.youtube.com/watch?v=nafoHAhz8Ys SHOPPING ------------------------------------------------ Important Note on Shopping: I'm not...

This design idea is not strategically brought into application. Due to the position of the fuel trailer the tank is subject to sudden explosions, if dealing with fire.Flamethrower battle tank made for 3D printing showcases the fuel trailer attached...

While every slicer is able to connect the blocks with a single extrusion wall, there seems to be none that does it in the (for stability reasons as well as for looks) only acceptable way of making this single extrusion a part of the upper wall...

... with M99. This may prevent dirtying up the bed and increase operational safety, especially if the model with brim is in the front centre of the push space. I'll add ideas as I test in the future and feel free to collaborate in the comments.

For the ones included, the idea is to mount the body to the bumper mount cross members. I like that solution because they are nice and inconspicuous but it means that my generic bumper mounts no longer work so I have been grappling with that...

i am making these to sell on ebay if you want one and do not have the tools or patiance of making these they are a lot of milling so far i have 3 single cooling blocks about 8 heat blocks and 1 or 2 duo blocks also there are 2 differant duo blocks...

... from one language to another may result in some nuances being lost or not fully captured. The translation provided is accurate to the best of my abilities, but it's always a good idea to review and verify any important information before using it.

This is to facilitate the sensor-induced low power mode, with the idea of conserving battery power if you run it off batteries. There're a couple things you can configure before flashing your Arduino: rf24_rx[5] - Is a 5-character channel that is...

... Changelog v1.7 - Fixed the eye features on the lid being 0.05 off from the base of the lid. Could cause print issues Changelog v1.7b - Fixed naming getting mixed up for the main units (No idea how or when. ...Thanks LocaCola for spotting this)

From now on, just mods :) If you have ideas for improving it beyond what I have done, let me know!V8.3 - Fixed the weird fragmentation on the shoulders from the original model. Converting to STL from SuperSlicer was slightly shifting things. This is...

Once the holes were drilled, I then held the assembled brackets and bars back up to the wagon and screwed the lath screws into the brackets to hold them in place on the wagon!NOTE: Since screw holes need to be drilled in the wagon for this design,...

Actually I liked the idea and like the 22l box size. What I did not like is that in most projects the bearing holders can cause friction on the bearing itself and the stands for the bearing rods were loosely coupled or even needed to be glued. So I...

Making them as strong as possible to prevent flexing is not a bad idea. How I Designed This This thing was made with Tinkercad. Get it <a href="https://www.tinkercad.com/things/9lmwyFJ4Kpc">here</a>.</p> <h3>How-to</h3> <p><strong>Grocery...

The cable stop and rollers are sized for that cable though. a 6 or 8 wire slip ring of some sort, I used this one: http://www.ebay.com/itm/141778020060?\_trksid=p2060353.m2749.l2649&amp;ssPageName=STRK%3AMEBIDX%3AIT For the waterproof version you...

... The idea behind it all was to put the on/off switch on the printer where it can turn itself off. The best place then turned out to be a point to the right of the X-axis that the printing carriage cannot normally reach due to the software end stops.

(if no cable is included with the end stops) A firmware to compile yourself (I used this here: https://github.com/davidramiro/Marlin-Ai3M-2.0.x) The Arduino IDE (https://www.arduino.cc/en/main/software) and a couple of printed end stop holders /...

Im just testing the idea out https://www.shapeways.com/shops/chito-1 This is a mount for the V6 hot-end by E3D that is stronger and more rigid than some of the mounts that are out there. This mount also comes with an array of possible options for any...

I wanted similar functionality, but also something more budget friendly.I can't take full credit for this idea - like I said there are others out there like it that you can buy, and even some other 3D designs out there. I just wanted to design one...