ideaformer 3d models
19 3d models found related to ideaformer.cults3d
Support for improvement and avoidance of Z- and Y-axis movements. ... printed with the ideaformer ir3
thingiverse
Es un soporte remix lo modifique un poco par usar en esta maquina. ... DESCARGAR E IMPRIMIR CON IDEAFORMER IR3
thingiverse
this is a mount for the stock extruder on the ideaformer IR3 3d printer to convert it from bowden to direct drive i designed this to print be printed by the ideaformer IR3 which seems to print mirrored so if you print on a different printer you may...
thingiverse
it is a fan shroud for the ideaformer pro 3d fdm printer. there are 2 files v4 has a 1mm fan mount and v5 has a 2mm fan mount, it will need longer screws to mount properly there might be some rough edges but it works pretty well. ... i...
thingiverse
Sherpa Mini Direct extruder mod for Ideaformer IR3
thingiverse
A dual mosfet holder for Anet A8 for the Ideaformer Mosfet
thingiverse
Replacement fan duct for the IdeaFormer Pro print head, previous one was too general in its air flow. ... Just print flat side to the bed, should be all good.
cults3d
BIGTREETECH TFT50 Remix + Ideaformer IR3 V1 mounting Remix of the BIGTREETECH TFT50 screen case ( https://www.thingiverse.com/thing:4570535 ) Based on the BIGTREETECH TFT 50 V3.0 Dummy screen layout ( https://www.thingiverse.com/thing:4704471 ) With...
thingiverse
Mount for ideaformer mosfet. Mounts to 2040 extrusion with M5 screws. No supports required. I printed in PETG, but should work in any filament. 4 M3 screws required to lock the mosfet board into place. Mounts to 2040 rail with two M5 x 8...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Designed to house a LED bar from Amazon. 14mmx14mm. Can be used on the CR-30 also. ...
thingiverse
love Sonicfury's design only issue I was having was between the extruder and the hot end the tube was popping out of the slot on the sherpa mini. so i added a quick 4M tap to the center hole for a JP4-01 Pneumatic Fitting. ...installed and everything...
grabcad
Mosfet from IdeaFormer on AliExpress; exact dimensions vary by approximately 0.15 millimeters.
prusaprinters
Einfacher Flowsplitter um den Luftstrom im Stock Fanduct des Ideaformer IR3 sauber aufzuteilen
thingiverse
Motors: * 4 x Nema17 motors - x,y,z,extruder - https://s.click.aliexpress.com/e/_DBXW4Nh (free shipping 7 day in europe) * 4 x 100cm XH2.54 Motor cables with connectors - IdeaFormer Store - https://s.click.aliexpress.com/e/_DlJT0Xp * 12 x M3X6mm -...
thingiverse
... кронштейна калибровки стола (еще не сделал). Кулеры пробовал разные, лучше всего дует от ideaformer. На Экструдер можно поставить как 40х40 через переходник, так и 30х30 штатный (если нет вибрации). Винты обычные М3 вкручиваются в пластик. ...
cults3d
So I decided to make one, fast to print and that pushes physics to its limits :p From one of the branches goes up to an inclination of 135°, while the other goes up to the horizontal and continues on 2cm, On this same side there is also an appendix...
prusaprinters
228.26mm.At this dimensions the opening hole has a diameter of 30mm and the tunnel shrinks down to 15mm at the inner end.Feel free to scale this model to make it fit your printbed and/or christmas tree.To get a nice looking pattern, I used the...