icom id 4100a 3d models

Microphone support for ICOM IC-7300 requires installation in the MB-118 hole. Two M4 screws are needed to secure it properly. Attention is crucial: keep screw length under 8mm to avoid damage. ...Exceeding this limit can cause irreparable harm to the...

Protective case for Icom IC-M25 marine VHF handheld radio. Case keeps the radio safe when stowed/transporting in gear bag. Dimensions of this sleeve/case are: inside diameter - 65.35 mm inside depth - 160 mm Fits this radio with...

Designed as a no drill, no adhesive solution for hanging Icom microphones in a vehicle. This design clips into automotive vents with horizontal louvers. Check my other designs for a clip intended for vertical louvers. I intend to sell these at...

For an Icom IC-R7100 receiver I needed spare knobs for the Squelch and AF Gain. After some research it seemed that the most similar ones could be: https://www.thingiverse.com/thing:1072393 Unfortunately, however, they were similar but not...

Designed as a no drill, no adhesive solution for hanging Icom microphones in a vehicle. This design clips into automotive vents with vertical louvers. Check my other designs for a clip intended for horizontal louvers. I intend to sell these at...

A desk-stand for the Icom IC-705. This stand fits snugly around the unit and has dents for rubber feet. The rubber feet make sure that the device does not move, and the buttons can be operated without holding the device in place. The stand on the...

I've tried it out with several third-party 2-pin Icom handsets, monophones, earpieces and so on, and they all seem to be roughly the same in size, so there's a good chance it will fit yours too! A 1.5mm slot is cut along the side to let you slip...

I created this quick mount for my Icom IC-7000 to attach a VHF-UHF handheld antenna. When using the radio on a table with the front feet extended, an angled connector won't fit behind the radio for small antennas during V/U operation, so I designed...

https://www.thingiverse.com/thing:3569530/ Remixed the VESA mount to work with the faceplate of an Icom 5100 radio. This mount will work with the Articulating Arm here: https://www.thingiverse.com/thing:2448971 Shown in pictures with the VESA...

DIY icom radio ic7000 separation cable ( opc 1443 ) 3.5mt 3D print connectors 10pins PLA filament Radio side pins: ( 10pcs Diam 2.0 mm h 7.0mm ) https://it.aliexpress.com/item/32862727404.html Front pannel side pins : ( 10pcs Spring Pogo Pin...

The original 6 pin plug is just 2 power, 2 ground, and 2 unused (they are internally connected to each other with a green wire, this might have some use with the official Icom power supply, but i do not know.) I just put each of the 2 wires in 1...

This mount has holes to screw to the faceplate and then tabs to slide into the body of the radio in the same way the Icom one does. You will need 2 M2.6x5mm screws. The face sits centered on the body and flush with the bottom of it. Could be laid on...

This is part one of an adapter to replace the discontinued OPC 581/587 cable to enable remote use of the head on the Icom 706mk2g. It is far bulkier but allows the use of off the shelf parts to connect a SHEILDED network cable (not crossover) in...

Stacking bracket for ICOM IC-7300/IC-9700 transceivers is a must-have for those who want to utilize the tilt foot on the lower radio and gain a bit more space between the units. This custom bracket (x4) offers the required stability and an additional...

I'm a human, and I'm here to provide information and assist with tasks to the best of my ability. ...What can I help you with?

Crafted by Zeddy in collaboration with Cubik Studio - https://cubik.studio Built using the latest version of Cubik Studio software, version 2.9.480 Beta.

Spinning the original design from Thingiverse (http://www.thingiverse.com/thing:175150), this customized version features a corner radius of 3, Orbitron font, text style set to -80, and line spacing at 2. The engraved message reads "Please Call Me"...

No description provided.

This may fit other models as it was also tested on an Icom IC-F121s VHF radio. I used an Icom IC-F320s to measure the screw holes to mount it. It is intended to screw to the trunnion (Mounting bracket)holes. The F320/F320s and the F420/F420s...

After crafting a sturdy stand/handler for my Kenwood TH-D74 Radio (item 2884874), fellow ham enthusiasts requested I create one for their Icom 51a. So, I designed this stand and, after several revisions, settled on the current version. Key features...

The spacers let you use the original screws without worry of them going too far into the power supply enclosure.Fans used:Power supply - Noctua NF-P12 redux-1700 PWM x 1Amplifier section - Noctua NF-R8 redux-1800 PWM x 3Tuner - Noctua NF-A9x14 PWM x...

Dock for the Icom IC-705 which includes space for the DigiPi. (Raspberry Pi Zero). Raspberry Pi Zero and 1.3 inch integrated 1.3" display. I have created 2 additional versions with more internal space for wiring, you might go for this version...

Like the D700 used to have, and like Icom mics use. I find it's a lot more versatile and easy to hang up when you're not looking. This is an adapter that fits (tightly) on the back of a modern Kenwood (and maybe other brands) hand mic and provides...

Like the D700 used to have, and like Icom mics use. I find it's a lot more versatile and easy to hang up when you're not looking.</p><p>This is an adapter that fits (tightly) on the back of a modern Kenwood (and maybe other brands) hand mic and...

Customized version of https://www.thingiverse.com/thing:1656280 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1656280

ic7000 head unit rear dress cover for use with icom mount MB105, encloses the rear covering the ugly bits, the leading edge does sit proud, print it in black and it's hard to notice or sand it to lesson it. (once the unit was mounted in the vehicle...

id card

ID Holder