icom id 4100a 3d models

This is a simple wedge-shaped stand for the ICOM ID-4100A dual-band mobile radio. It is designed to lift the radio off a desk and make the screen/buttons more accessible. Given the relatively-close dimensions of the older ICOM IC-880H, it should...

This is a simple wedge-shaped stand for the ICOM ID-4100A dual-band mobile radio, designed to lift it off any desk and make the screen/buttons more accessible at all times. Its relatively-close dimensions to the older ICOM IC-880H suggest that it...

This is a simple wedge-shaped stand for the ICOM ID-4100A dual-band mobile radio. It is designed to lift the radio off a desk and make the screen/buttons more accessible. Given the relatively-close dimensions of the older ICOM IC-880H, it should work...

This is a simple wedge-shaped stand for the ICOM ID-4100A dual-band mobile radio. It is designed to lift the radio off a desk and make the screen/buttons more accessible. Given the relatively-close dimensions of the older ICOM IC-880H, it should work...

ICOM ID-4100A Radio Mount Specifically Designed for the Scion tC Model

Mount for Icom ID-4100. v1 - It works so unless I find some flaws as I use it I don't suspect I'll revise it. There is about 1mm gap from the radio on each side. Using 4 m4x8 screws I was able to cleanly attach the radio. There are 4 mounting...

Holder for ID-51 to be placed on the table. Can also be permanently installed. ... Using with any PLA

The Icom ID-51 is held securely by a straightforward stand that provides easy access to its charging ports through strategically placed cutouts.

... magnets/plate to be installed on the back of the faceplate. There is a finger groove for leverage against the touch screen so it doesn't slide around when you're operating it. (tags) Icom ID-5100a 5100 ID5100 HAM amateur Radio ICOM Yaesu Kenwood

Magnetic Mount Companion: Attach this component to the built-in magnetized bracket on your Icom ID-5100, then securely fasten it to any vehicle's 1-inch RAM mounting system for versatile placement.

The ICOM ID-5100 display stand hooks up directly to the radio's main body via its original lateral screw connection. Print Settings: Printer: ZORTRAX M200 Rafts: Yes, this printer supports raft printing. Supports: The ZORTRAX M200 can print...

I wanted a simple and quick to print desktop stand for the Icom ID-5100 front panel. I'm planning on using the radio in a couple of vehicles so I'll be moving it around. The stands and the front panel don't weigh much so if you set it up in front of...

This is a custom RAM Mount holder designed specifically for the iCOM ID-51. It accommodates both the larger battery and the standard issue battery, ensuring a secure fit every time. The holder's framework is built using M4X25 screws, providing a...

ICOM ID-4100 Head Bracket V1 ============================ After the original bracket broke, I decided to create something better. ICOM is great, but their proprietary mounting system leaves much to be desired. As such, here's a new bracket that...

Engineered specifically for the ID-880H remote head, this underside mount is crafted to be printed in two seamless parts that bond effortlessly together.

May 2020 From Randy - W4LKS ICOM ID-51 3D Printed Desktop Stand This simple desktop stand cradles your ICOM ID-51 at a comfortable viewing angle on your desk, allowing you to easily monitor the screen while keeping the radio within easy reach. The...

This is a display stand for the Icom ID-5100. This stand can be installed on the radio or it can be used on the desk. The display can be attached directly with the two rear screws or it can be attached with the MBA-2 kit with the moguls to be able...

This is a set of brackets to hang an Icom ID-4100 VHF/UHF/DSTAR Mobile Radio and Icom SP-35 Mobile Speaker. They are designed so the speaker and radio front are close to the same plane when mounted. Icom no longer includes the MBF-4 mounting...

ICOM doesn't make anything for the that so I did. This is uses a counterbored bolt in the center for the Lido mount. ... http://www.lidomounts.com/homepage.html Instructions Print in ABS or it will...

This is a quick and dirty stand to allow you to keep the ID-5100A head unit vertically mounted on a desk. It's not locked into the stand, so its free to move around, but there is a cutout for ventilation that needs to line up with the vents on one...

An existing cellphone mount in my truck inspired me to use a printed baseplate, transforming it into a convenient location for attaching the ID-800H's tuning head. The baseplate was 3D printed using PLA and 25% infill. ...Although it may require some...

This creation was crafted using Tinkercad's powerful tools. ...To make changes, simply visit the website at https://www.tinkercad.com and select the edit option for this design: 0dGnhblBPDL.

For some time, I'd used a pair of zip ties to keep the SP-35 speaker attached to the suction cup mount for the Icom ID-5100 controller head, but this 3d printed bracket is a sturdier (and tidier!) solution.You will need:The Icom ID-5100 (may worth...

Here is a custom model, created using the Thingiverse Customizer. ... Design Parameters: Angle to rotate: 340 degrees Wall thickness: 4 millimeters Top layer height: 70 millimeters Total object length: 28 millimeters Side view angle: 65 degrees ...

Pause at 35mm and insert screw washer 18x1.6mm.

Super Simple Spacer for Icom ID-52 with a Signal Stick BNC adaptor as it doesn't quite fit snugly.Not much to it but I know one person who'll find it useful.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4uRJPeqA6ub

Dies ist ein Ständer um das RX/TX-Modul senkrecht stellen zu können. Zur Montage im Kofferraum musste ich den Sendeblock höher haben um einen möglichen Wasserschaden durch eindringendes Wasser vorzubeugen. Macht sich aber im Shack auch ganz gut um...