icom id 4100 3d models

I simply added a front support with mounting holes to hold the metal baseplate for the Icom ID-5100 transceiver. The addition is a little rough around the edges, but, it works fine and isn't seen when the draw is in position. The draw space is...

For installing an Icom 706 shortwave transceiver into a portable case you can use this holder to fix the transceiver in the case. With the sliders for the screws (15mm x 4mm) you can mount it in the holder and slide it into its working position.

 The adapter plate sold by Icom was 40 bucks so I just printed up this adapter plate for a few cents.If this is going in a vehicle, I'd recommend a higher temp filament such as PETG or ASA. ... I printed this one in PETG.Printer:Ender 3 pro with Sprite...

This eliminates the need for ICOM MBA-5 ($40) and 20mm RAM/AMPS plate ($15) Designed in Auto CAD Sliced using Cura Printed successfully on Ender-3 100% infill PLA 220deg / 55deg bed Requires 2x M2.6 x 10MM machine screws for attachment to faceplate....

Microphone support for ICOM IC-7300 requires installation in the MB-118 hole. Two M4 screws are needed to secure it properly. Attention is crucial: keep screw length under 8mm to avoid damage. ...Exceeding this limit can cause irreparable harm to the...

Protective case for Icom IC-M25 marine VHF handheld radio. Case keeps the radio safe when stowed/transporting in gear bag. Dimensions of this sleeve/case are: inside diameter - 65.35 mm inside depth - 160 mm Fits this radio with...

This is a replacement knob for an Icom IC7200 Twin PBT. If you're unfortunate enough to lose the top filter knob (and you've finished crying) this might be an ok replacement.It was modeled in Blender to look as much like original as possible. ...It's...

The housing will contain six arcade buttons, specifically Sanwa OBSF-24 models, and integrate seamlessly with an iCom microphone to grant instant access to push-to-talk and memory keyer functions during competitions. ... This is the second major...

This is a Mount to place the Leo Bodnar 10MHz reference mini GPS module on the side of the ICOM IC-9700 radio. ... This uses 2x M4x8mm screws (MAX 8mm, or you will damage the radio) I printed this side on, with supports on build plate only, 0.2mm,...

... It's a creation that wasn't initially mine, but I tailored the dimensions to fit the Icom IC-V82 perfectly, as well as the Baofeng GT-3. ...This design is suitable for both wallmount and suction cup mounting options.

This adapter is specifically designed for older Icom, Kenwood, Yaesu radios. The original design had six pins, but this model has been simplified to just four. Interestingly, only two of these pins are needed to provide power to the radio. ...I've...

This is a very simple and small tilt stand for the Icom IV-705. It requires two knurled M4x12 to mount it on the radio. ...I used https://amzn.to/48Lv9ymI also put a couple of small stick-on rubber feet at the bottom rear corners of the radio to keep it...

Designed as a no drill, no adhesive solution for hanging Icom microphones in a vehicle. This design clips into automotive vents with vertical louvers. Check my other designs for a clip intended for horizontal louvers. I intend to sell these at...

A desk-stand for the Icom IC-705. This stand fits snugly around the unit and has dents for rubber feet. The rubber feet make sure that the device does not move, and the buttons can be operated without holding the device in place. The stand on the...

Designed as a no drill, no adhesive solution for hanging Icom microphones in a vehicle. This design clips into automotive vents with horizontal louvers. Check my other designs for a clip intended for vertical louvers. I intend to sell these at...

For an Icom IC-R7100 receiver I needed spare knobs for the Squelch and AF Gain. After some research it seemed that the most similar ones could be: https://www.thingiverse.com/thing:1072393 Unfortunately, however, they were similar but not...

I've tried it out with several third-party 2-pin Icom handsets, monophones, earpieces and so on, and they all seem to be roughly the same in size, so there's a good chance it will fit yours too! A 1.5mm slot is cut along the side to let you slip...

I created this quick mount for my Icom IC-7000 to attach a VHF-UHF handheld antenna. When using the radio on a table with the front feet extended, an angled connector won't fit behind the radio for small antennas during V/U operation, so I designed...

DIY icom radio ic7000 separation cable ( opc 1443 ) 3.5mt 3D print connectors 10pins PLA filament Radio side pins: ( 10pcs Diam 2.0 mm h 7.0mm ) https://it.aliexpress.com/item/32862727404.html Front pannel side pins : ( 10pcs Spring Pogo Pin...

https://www.thingiverse.com/thing:3569530/ Remixed the VESA mount to work with the faceplate of an Icom 5100 radio. This mount will work with the Articulating Arm here: https://www.thingiverse.com/thing:2448971 Shown in pictures with the VESA...

The original 6 pin plug is just 2 power, 2 ground, and 2 unused (they are internally connected to each other with a green wire, this might have some use with the official Icom power supply, but i do not know.) I just put each of the 2 wires in 1...

This mount has holes to screw to the faceplate and then tabs to slide into the body of the radio in the same way the Icom one does. You will need 2 M2.6x5mm screws. The face sits centered on the body and flush with the bottom of it. Could be laid on...

This is part one of an adapter to replace the discontinued OPC 581/587 cable to enable remote use of the head on the Icom 706mk2g. It is far bulkier but allows the use of off the shelf parts to connect a SHEILDED network cable (not crossover) in...

Stacking bracket for ICOM IC-7300/IC-9700 transceivers is a must-have for those who want to utilize the tilt foot on the lower radio and gain a bit more space between the units. This custom bracket (x4) offers the required stability and an additional...

No description provided.

I'm a human, and I'm here to provide information and assist with tasks to the best of my ability. ...What can I help you with?

Crafted by Zeddy in collaboration with Cubik Studio - https://cubik.studio Built using the latest version of Cubik Studio software, version 2.9.480 Beta.

Spinning the original design from Thingiverse (http://www.thingiverse.com/thing:175150), this customized version features a corner radius of 3, Orbitron font, text style set to -80, and line spacing at 2. The engraved message reads "Please Call Me"...