icom id 4100 3d models

The included circuit diagram from the Icom 7610 basic manual can be reproduced in veroboard (or make your own pcb) and fitted inside the printed case. The dimensions of the case allow it to sit under the front of the 7610. Make your veroboard or...

I wanted to get a carrying handle for my ICOM IC-718, so I looked into purchasing one from ICOM. However, I decided it would be easier and more cost-effective to design and print my own. The handle turned out great when printed with PLA, but I plan...

The shround will space the plugs correctly for the radio at the correct depth, and will fit any of the IC-41 series UHF radios or the Icom A15 and A16 (and maybe the A25). Note the connnection will NOT be waterproof. Additional parts required:...

Icom IC-705 protective shield. This is a 2 parts shield so it can fit in any 3D printer. Glueing the inserts with "Loctite" or similar is strongly recommended. When printing, use Tree Support and position the part in the bed as in the shared...

This volume/squelch knob for the Icom IC-H16T is designed to be compatible, with the same shaft design as the original model. The originals feature a knurled rubber ring for grip, but I opted for coarse splines to simplify the printing process. A...

I came across Fabianomoser Icom 9700 stand and after printing it out I decided I would like the stand rail to be a bit more deeper and less of a gap between the top of the stand and the bottom of the radio. I also cut a large square threw the stand...

I came across Fabianomoser Icom 7300 stand and after printing it out I decided I would like the stand rail to be a bit more deeper and less of a gap between the top of the stand and the bottom of the radio. I also cut a large square threw the stand...

I designed this R8600 stand to match my other icom stands LETTERS NOTES The lettering is 3mm deep in the stand and the lettering print is 2mm thick. I did drop the X axis down to 99.25% (Y & Z left at 100%) when slicing to help the letters squeeze...

I came across Fabianomoser Icom 9700 stand and after printing it out I decided I would like the stand rail to be a bit more deeper and less of a gap between the top of the stand and the bottom of the radio. I also cut a large square threw the stand...

This is a pair of rails that can be attached to the Icom IC-7000 radio to protect its front and back when operating portable. They are mounted to the radio using the same holes and screws used for the mobile base. Each rail measures 236 mm in length,...

I came across Fabianomoser Icom stands 7300/9700 and after printing them out I decided I would like the stand rail to be a bit more deeper and less of a gap between the top of the stand and the bottom of the radio.so i designed mine for the 7300/9700...

** This is a work in progress ** I could not justify the cost of the ICOM LC-192 for my IC-705 radio. So instead I decided to adapt a low cost (£23) “sling” camera bag. A sling bag is one that can be carried on your back or swung round onto the...

radio set ICOM IC-M200

ICOM 7300 Side Rails. ...Protects Knobs while out and about.

Meter Switch Roulette of the HF Transceiver Icom IC-775DSP.

Tilt bail for icom 705 qrp transceiver. ...Printing time about 25min on CR-10

Icom BP-272 Battery Protector Case The battery stay in place when using the belt clip.

Icom IC-705 Antenna Bracket for SO239 connector. ... Antenna strain relief.

Stand for ICOM IC-705 to have a better look at the screen. ...

shovel door p&h 4100 xpc scale 1:25.

The iconic Icom HF radio is designed for enthusiastic ham operators to communicate via high frequency bands.

Here is a Remix of the Excellent IC-A4 Charger Base, Tailored for Seamless Use with the Icom IC-92AD Amateur Radio.

Cradle mount for ICOM HM-234 microphone, for use with clip that comes fitted to the mic. ...(This is the microphone supplied with the IC-705.)

Extension Feet for ICOM 7700-7800-7851 ... ... Due lo missing them I designed my own Fixed them with a bit of double side tape

This is a microphone clip for the Icom HM-151 style microphone. ... The mic often comes standard with IC-7000 and IC-7100 amateur radios. Check out my post on this topic for more details

Icom, Baofeng, Kenwood, and other radios use a very similar-looking plug but they are not compatible electrically. Icom stands out as the odd one out. Plugs and accessories for Baofengs are common and cheap but don't work with Icom. The cheap plugs...

I have both the IC2730a and the ID-5100a and can confirm it fits both radios. It may fit others that take the MBA-2 or MBA-5 style faceplate mount, they both have the same spread on the mounting holes. I used the original icom screws that I had. ...

ICOM IC-2730E ICOM Mobile Transceiver Mounting Bracket. Something similar to original Icom MBA-4. You can mount control head to main body. You can still connect microphone to main body or control head, there should be some room for cables. I...

ICOM IC-2730E ICOM Mobile Transceiver Mounting Bracket. Something similar to original Icom MBA-4. You can mount control head to main body. You can still connect microphone to main body or control head, there should be some room for cables. I have...

Icom remote head mounting plates with standard AMPS pattern for connecting to different bases. ...Included is the standard thin version plus a thicker one for a more robust mount.