icom ic r3 3d models

External speaker enclosure for Icom radios. ... This enclosure is styled and sized to match either the IC-7300 or IC-9700 radios. ... Designed for a standard 66mm 8 ohm speaker.

Transceiver ICOM IC-2730 Multi Functional Bracket use it on the wall, in your car, or in the field or on your desktop. With this bracket you can do it all. Use this bracket for your ICOM IC-2730 transceiver. You need 4x Cyl. ...head screws M4x20mm

2 Poignées de protection pour Icom IC-7300 (idem 9700) 3 vis de fixation a gauche et 2 vis a droite Liberté de manipulation des boutons (rotation VFO) 2 protective handles for Icom IC-7300 with (same 9700) 3 fixing screws on the left and 2 screws on...

Thanks to colleague Valério PY1WZ for donating his original contribution to Júnior PY1JR and overseeing 3D design, we now have the Release button front panel Icom IC-706. I'm hoping this can be helpful. ...73 from PT7KM.

Protective case for Icom IC-M25 marine VHF handheld radio. Case keeps the radio safe when stowed/transporting in gear bag. Dimensions of this sleeve/case are: inside diameter - 65.35 mm inside depth - 160 mm Fits this radio with...

... It's a creation that wasn't initially mine, but I tailored the dimensions to fit the Icom IC-V82 perfectly, as well as the Baofeng GT-3. ...This design is suitable for both wallmount and suction cup mounting options.

Microphone support for ICOM IC-7300 requires installation in the MB-118 hole. Two M4 screws are needed to secure it properly. Attention is crucial: keep screw length under 8mm to avoid damage. ...Exceeding this limit can cause irreparable harm to the...

I purchased a new mount for the control head of my Icom IC-2730A amateur radio.  The mount uses the standard AMPS profile mounting pattern, but the radio has a custom spaced mounting pattern.  The adapter plate sold by Icom was 40 bucks so I just...

For an Icom IC-R7100 receiver I needed spare knobs for the Squelch and AF Gain. After some research it seemed that the most similar ones could be: https://www.thingiverse.com/thing:1072393 Unfortunately, however, they were similar but not...

A desk-stand for the Icom IC-705. This stand fits snugly around the unit and has dents for rubber feet. The rubber feet make sure that the device does not move, and the buttons can be operated without holding the device in place. The stand on the...

I created this quick mount for my Icom IC-7000 to attach a VHF-UHF handheld antenna. When using the radio on a table with the front feet extended, an angled connector won't fit behind the radio for small antennas during V/U operation, so I designed...

Simple desktop holder for control panel to Icom IC2730. ...

I adapted rdcole's design to fit in my Icom IC-718 in place of the molex style power socket. I find the original power plug gets loose, gets hot, and starts to melt. This will allow you to convert the radio to Anderson Power Poles. This fits the...

This is a piece to keep a standard size of earpiece plugs aligned with the top of the Icom IC-T70 radio. I've tried it out with several third-party 2-pin Icom handsets, monophones, earpieces and so on, and they all seem to be roughly the same in...

Dock for the Icom IC-705 which includes space for the DigiPi. (Raspberry Pi Zero). Raspberry Pi Zero and 1.3 inch integrated 1.3" display. I have created 2 additional versions with more internal space for wiring, you might go for this version...

Stacking bracket for Icom IC-7300 and IC-7300 radios. Safe space in your shack by stacking your radios on top of each other. Do not use this for portable operations. I have been printing these with PLA and they hold up the weight just fine due to...

This is a very simple and small tilt stand for the Icom IV-705. It requires two knurled M4x12 to mount it on the radio. ...I used https://amzn.to/48Lv9ymI also put a couple of small stick-on rubber feet at the bottom rear corners of the radio to keep it...

Remote Head Plate for Mounting IC-7000 Elsewhere, I've Kept it Bare with No Screw Holes to Make Your Own or Attach It to a Satnav Mount on the Glass - Version 1

This is a stand for the IC-R6, due to the radio's compact size it doesn't like to stand on its own and is a pain to display on a desk. this stand allows the radio to be displayed on a desk and used without it falling onto its back. ...

This is a stand for the IC-R6, due to the radio's compact size it doesn't like to stand on its own and is a pain to display on a desk. this stand allows the radio to be displayed on a desk and used without it falling onto its back. ...Print Settings...

In addition to the keypad a paddle or straight key has to be connected to the key connector of the IC-705. Therefore my keypad has two femal socket jacks 3.5 mm which are parallel connected. One for a 3-wire (stereo) cable to the transceiver and one...

[UPDATE 7 Aug] Updated the XL versions to give more space for the microphone and a better fit overall.[UPDATE 18 Jun] Added an XL version with a compartment to hold the speaker-microphone.This is two items, a full cover for the Icon IC-705 ham radio...

I had to secure my IC-7100 to my car bracket, but the included mounting hardware didn't fit the mounting holes on the bottom of my head unit. I have two sets of screws, a 1/4-20 "tripod" like screw and three M3 screw holes, but I couldn't find a...

Recently got an IC-R10, it had no belt clip. I have a 3d printer and Fusion360. Now here we are.</p><p>Threading of the inserts is M3. I used M3x6mm socket head screws and modeled with them in mind. For reference, the space between inserts is...

Remixed ICOM IC-705 antenna bracket with N connector instead a BNC and made in one solid piece

Face protector I made for the ICOM IC-705.Provided STL with Callsign and also STL with blank screen.

Stand could be equipped with contacts for charging wthe battery. enough space vor chargingelectronics in the rear. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/2NN3ZAVwd2L

My young boy removed the original handles by his own two hands and promptly misplaced them like kids often do, so instead of running out to buy new ones, which was certainly an option, I took matters into my own hands and designed and printed some...

A VHF/UHF transceiver is a device that enables communication by transmitting and receiving signals within the Very High Frequency (VHF) and Ultra High Frequency (UHF) bands. It combines a transmitter and receiver in one unit, allowing for two-way...

<p>0.15 / 20min / filament 50sm&nbsp;</p>