icom 4100 3d models

Vehicle bracket for icom 3230h or similar, it is quite stable but to fix it I suggest transparent double-sided adhesive.The width is suitable for a maximum radius of 145mmStaffa veicolare per icom 3230h o simili, è abbastanza stabile ma per fissarla...

In order to use 3xAAA batteries, you need the spacer, as it presses down on the PCB thru a whole, likely in order to tell the iCOM to have a different voltage, Place this spacer in our iCOM and then insert the batteries and all should be good. ... You...

I took the Size B (1 inch) Ram Mount ball From Ozy's mount and put it on aomitri's ICOM 2730a faceplate mount. ... RESULT: IC-2730a faceplate mount w/ Size B (1") Ram Mount ball.

I'm wrapping a convenient cover around the two RJ45 panel mounts that connect my Mic and Head Unit to the Icom IC-7100 with my trusty Go-Box.

For some time, I'd used a pair of zip ties to keep the SP-35 speaker attached to the suction cup mount for the Icom ID-5100 controller head, but this 3d printed bracket is a sturdier (and tidier!) solution.You will need:The Icom ID-5100 (may worth...

... LDG-AT7000 tuner, combining the radio and tuner for easier mobile use. ...This setup may also work for Icom 706 series radios, although I haven't tested it on one. Feel free to use this mount as you see fit, but please don't sell it! ...Cheerz Adrian

My buddy scored an Icom 5100, proudly displaying it on his desk, and he needed a mic clip to complete the setup. ...So, I decided to take Houston's design and give it a boost by adding countersunk holes for easy mounting.

This is a Mount to place the Leo Bodnar 10MHz reference mini GPS module on the side of the ICOM IC-9700 radio.This uses 2x M4x8mm screws (MAX 8mm, or you will damage the radio)I printed this side on, with supports on build plate only, 0.2mm, PETG for...

ICOM 2730A faceplate bracket to stay on top of my monitor. The monitor is the LG 24M37H-B. You can also add a thin strip of double sided tape on the back to prevent shifting. ... It fit's tight on mine, so I don't need any.

This is a protective frame / handle assembly designed specifically for the ICOM IC-7300. It extends fully around the radio, with only slight protrusions at the top and bottom, giving it an almost military-like appearance that's sure to turn heads. ...To...

This is version 2 of my Icom IC-2AT speaker microphone port cover. Version 2 is made from TPU and goes around the BNC antenna connector. ... The original was made using PLA and can be found here: https://www.thingiverse.com/thing:3736393

NiCD battery performance is disappointing so I decided to design my own BP-173 compatible battery pack with two 18650s inside, providing 7-8 volts for Icom W32E (and other BP173/BP180 radios). 1. Print all parts, 0.2 mm layer, 3 walls, supports...

This is a simple wedge-shaped stand for the ICOM ID-4100A dual-band mobile radio, designed to lift it off any desk and make the screen/buttons more accessible at all times. Its relatively-close dimensions to the older ICOM IC-880H suggest that it...

Given the relatively-close dimensions of the older ICOM IC-880H, it should work pretty well with that radio as well. This is the fourth revision to the design and is the only one I consider worthy of publishing. I have designed a complementary...

Needed a Yaesu mic adapter that would fit on this Icom HM-151 holder (https://www.thingiverse.com/thing:2334907) which is a bit wider than some of the other ones you can purchase from retailers. It seems pretty strong when printing flat and I've...

This is a stand for the body of the Icom 2730 or Anytone AT-5888UV or any other mobile radio where the mounting holes on the body are spaced 50mm apart. It positions the radio at a 10 degree incline when placed on a level surface. I printed with 3...

If you need to install nickel or alkaline batteries in your icom receiver, you'll notice it won't power up. This is because certain tabs make contact with the batteries to provide power. The original design includes spacers for the batteries, but...

The frame designed by Andrew Brierley for the ICOM IC-7300 turned out great, but unfortunately, it wouldn't fit in my printer because the part is 280mm long. To print this item, I had to cut it in half. ...Printing two of each part is required; the A...

Stacking bracket for Icom IC-7300 and IC-7300 radios. Safe space in your shack by stacking your radios on top of each other. Do not use this for portable operations. I have been printing these with PLA and they hold up the weight just fine due to...

Given the relatively-close dimensions of the older ICOM IC-880H, it should work pretty well with that radio as well. This is the fourth revision to the design and is the only one I consider worthy of publishing.</p> <p>I have designed a complementary...

... Loaded Test Probes Pogo Pins tool RM (Ebay) (334202545452) Ribbon cable of appropriate size. M3 screws This design is to replace the cabin light cluster in the Mitsubishi ASX with an adapter to fit the Icom 706 mk2g head above the driver. ...

Given the relatively-close dimensions of the older ICOM IC-880H, it should work pretty well with that radio as well. This is the fourth revision to the design and is the only one I consider worthy of publishing. I have designed a complementary...

... on both ends so you can attach anything you like on top. On the top of the axis, I have mounted a custom base I designed that attaches to the central piece of the Icom MBF-1 suction mount. ...Then I can mount the head of my IC-7000 and operate.

SImple enclosure for Sure Wondom JAB5 and Dyton Audio KABD 4100 amplifiers. ...

This mounting device is designed for the Dräger Helmets HPS 4100 and HPS 4300 and is intended to secure the Led Lenser P7R, P7.2, P7, P4X, and T2 on the helmet. I tested it on functionality, but not under harsh conditions yet. I also uploaded the...

Dräger PX1/UK4 GoPro Bracket for Fire Helmet HPS 4100 / HPS 4300 This action camera mount is designed to accommodate not only the 3 and 4-generation GoPro cameras, but also other action cameras from various manufacturers. It was specifically...

Ich habe eine Halterung für mein Handfunkgerät auf dem Boot gebraucht. Ständig flog das Teil, dass ich tatsächlich fast ausschliesslich in Schleusen benutze, in der Gegend rum. ...Da es äusserst unproduktiv ist, alles irgendwo auf dem Tisch rumfliegen...

Antenna bracket for the IC-705 radio. You can include antenna ground (blue plug on my design). ...For heavy antennas like ATX-1080 or others.

Support for MD380/MD390 or any handheld radio is available.

Printed a protective cover for the 705. All connectors are still accessible. Cover and 705 are connected with the 4 M4 screws at the bottom. Will make some improvements over time. ...Good luck 73 de ON4VH.