icom 2730a mount 3d models

Protective case for Icom IC-M25 marine VHF handheld radio. Case keeps the radio safe when stowed/transporting in gear bag. Dimensions of this sleeve/case are: inside diameter - 65.35 mm inside depth - 160 mm Fits this radio with...

This is a replacement knob for an Icom IC7200 Twin PBT. If you're unfortunate enough to lose the top filter knob (and you've finished crying) this might be an ok replacement.It was modeled in Blender to look as much like original as possible. ...It's...

Designed as a no drill, no adhesive solution for hanging Icom microphones in a vehicle. This design clips into automotive vents with horizontal louvers. Check my other designs for a clip intended for vertical louvers. I intend to sell these at...

For an Icom IC-R7100 receiver I needed spare knobs for the Squelch and AF Gain. After some research it seemed that the most similar ones could be: https://www.thingiverse.com/thing:1072393 Unfortunately, however, they were similar but not...

Designed as a no drill, no adhesive solution for hanging Icom microphones in a vehicle. This design clips into automotive vents with vertical louvers. Check my other designs for a clip intended for horizontal louvers. I intend to sell these at...

A desk-stand for the Icom IC-705. This stand fits snugly around the unit and has dents for rubber feet. The rubber feet make sure that the device does not move, and the buttons can be operated without holding the device in place. The stand on the...

DIY icom radio ic7000 separation cable ( opc 1443 ) 3.5mt 3D print connectors 10pins PLA filament Radio side pins: ( 10pcs Diam 2.0 mm h 7.0mm ) https://it.aliexpress.com/item/32862727404.html Front pannel side pins : ( 10pcs Spring Pogo Pin...

The original 6 pin plug is just 2 power, 2 ground, and 2 unused (they are internally connected to each other with a green wire, this might have some use with the official Icom power supply, but i do not know.) I just put each of the 2 wires in 1...

Stacking bracket for ICOM IC-7300/IC-9700 transceivers is a must-have for those who want to utilize the tilt foot on the lower radio and gain a bit more space between the units. This custom bracket (x4) offers the required stability and an additional...

This is part one of an adapter to replace the discontinued OPC 581/587 cable to enable remote use of the head on the Icom 706mk2g. It is far bulkier but allows the use of off the shelf parts to connect a SHEILDED network cable (not crossover) in...

I ordered a Diamond BNC to SMA adapter for my ICOM ID-52 and wasn't pleased with the gap in between the adapter and antenna base around the SMA post. This will perfectly fill the gap. I've provided 2 slightly differing files. 1 is a spacer that...

The spacers let you use the original screws without worry of them going too far into the power supply enclosure.Fans used:Power supply - Noctua NF-P12 redux-1700 PWM x 1Amplifier section - Noctua NF-R8 redux-1800 PWM x 3Tuner - Noctua NF-A9x14 PWM x...

Dock for the Icom IC-705 which includes space for the DigiPi. (Raspberry Pi Zero). Raspberry Pi Zero and 1.3 inch integrated 1.3" display. I have created 2 additional versions with more internal space for wiring, you might go for this version...

After crafting a sturdy stand/handler for my Kenwood TH-D74 Radio (item 2884874), fellow ham enthusiasts requested I create one for their Icom 51a. So, I designed this stand and, after several revisions, settled on the current version. Key features...

Like the D700 used to have, and like Icom mics use. I find it's a lot more versatile and easy to hang up when you're not looking. This is an adapter that fits (tightly) on the back of a modern Kenwood (and maybe other brands) hand mic and provides...

Like the D700 used to have, and like Icom mics use. I find it's a lot more versatile and easy to hang up when you're not looking.</p><p>This is an adapter that fits (tightly) on the back of a modern Kenwood (and maybe other brands) hand mic and...

This is a quick and dirty stand to allow you to keep the ID-5100A head unit vertically mounted on a desk. It's not locked into the stand, so its free to move around, but there is a cutout for ventilation that needs to line up with the vents on one...

Customized version of https://www.thingiverse.com/thing:1656280 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1656280

This is a Mount to place the Leo Bodnar 10MHz reference mini GPS module on the side of the ICOM IC-9700 radio.This uses 2x M4x8mm screws (MAX 8mm, or you will damage the radio)I printed this side on, with supports on build plate only, 0.2mm, PETG for...

My buddy scored an Icom 5100, proudly displaying it on his desk, and he needed a mic clip to complete the setup. ...So, I decided to take Houston's design and give it a boost by adding countersunk holes for easy mounting.

This is a stand for the body of the Icom 2730 or Anytone AT-5888UV or any other mobile radio where the mounting holes on the body are spaced 50mm apart. It positions the radio at a 10 degree incline when placed on a level surface. I printed with 3...

Remixed ICOM IC-705 antenna bracket with N connector instead a BNC and made in one solid piece

Face protector I made for the ICOM IC-705.Provided STL with Callsign and also STL with blank screen.

Smiley Rubber Duck antennas when ordered with the "MX" connector work on just about every ICOM commercial portable radio. I think they're a great upgrade from the ICOM OEM antennas, especially the shorty's on the F1000 & F2000. ... This was actually...

These are feet for ICOM 746, 7400 etc. ...I don't know where else they can fit, I assume the same for the 756 and 7410.

I lost my Icom V85 volume knob. Printed this one to be a snug fit. Works like a charm. ... Fusion 360 editable file attached too.

I detest it when my radios topple over, fortunately, this sturdy stand ensures your IC-91A remains upright and secure on any flat surface, whether it's a tabletop or another even ground.

PTT switch adapter crafted for Yaesu and Kenwood radios, meticulously replicated from original Yaesu MH-31 design specifications.

Radio microphone

This creation was crafted within the digital realm of Tinkercad, a powerful tool for shaping imagination into reality. ...To see its inner workings and offer your own touch, visit https://www.tinkercad.com/things/hXPXyG2Ku97.