icom 208h 3d models

Protective case for Icom IC-M25 marine VHF handheld radio. Case keeps the radio safe when stowed/transporting in gear bag. Dimensions of this sleeve/case are: inside diameter - 65.35 mm inside depth - 160 mm Fits this radio with...

This is a set of brackets to hang an Icom ID-4100 VHF/UHF/DSTAR Mobile Radio and Icom SP-35 Mobile Speaker. They are designed so the speaker and radio front are close to the same plane when mounted. Icom no longer includes the MBF-4 mounting...

This is a display stand for the Icom ID-5100. This stand can be installed on the radio or it can be used on the desk. The display can be attached directly with the two rear screws or it can be attached with the MBA-2 kit with the moguls to be able...

ICOM doesn't make anything for the that so I did. This is uses a counterbored bolt in the center for the Lido mount. ... http://www.lidomounts.com/homepage.html Instructions Print in ABS or it will...

This is a Mount to place the Leo Bodnar 10MHz reference mini GPS module on the side of the ICOM IC-9700 radio. ... This uses 2x M4x8mm screws (MAX 8mm, or you will damage the radio) I printed this side on, with supports on build plate only, 0.2mm,...

This is a very simple and small tilt stand for the Icom IV-705. It requires two knurled M4x12 to mount it on the radio. ...I used https://amzn.to/48Lv9ymI also put a couple of small stick-on rubber feet at the bottom rear corners of the radio to keep it...

A desk-stand for the Icom IC-705. This stand fits snugly around the unit and has dents for rubber feet. The rubber feet make sure that the device does not move, and the buttons can be operated without holding the device in place. The stand on the...

For an Icom IC-R7100 receiver I needed spare knobs for the Squelch and AF Gain. After some research it seemed that the most similar ones could be: https://www.thingiverse.com/thing:1072393 Unfortunately, however, they were similar but not...

Designed as a no drill, no adhesive solution for hanging Icom microphones in a vehicle. This design clips into automotive vents with horizontal louvers. Check my other designs for a clip intended for vertical louvers. I intend to sell these at...

Designed as a no drill, no adhesive solution for hanging Icom microphones in a vehicle. This design clips into automotive vents with vertical louvers. Check my other designs for a clip intended for horizontal louvers. I intend to sell these at...

I've tried it out with several third-party 2-pin Icom handsets, monophones, earpieces and so on, and they all seem to be roughly the same in size, so there's a good chance it will fit yours too! A 1.5mm slot is cut along the side to let you slip...

https://www.thingiverse.com/thing:3569530/ Remixed the VESA mount to work with the faceplate of an Icom 5100 radio. This mount will work with the Articulating Arm here: https://www.thingiverse.com/thing:2448971 Shown in pictures with the VESA...

I created this quick mount for my Icom IC-7000 to attach a VHF-UHF handheld antenna. When using the radio on a table with the front feet extended, an angled connector won't fit behind the radio for small antennas during V/U operation, so I designed...

DIY icom radio ic7000 separation cable ( opc 1443 ) 3.5mt 3D print connectors 10pins PLA filament Radio side pins: ( 10pcs Diam 2.0 mm h 7.0mm ) https://it.aliexpress.com/item/32862727404.html Front pannel side pins : ( 10pcs Spring Pogo Pin...

The original 6 pin plug is just 2 power, 2 ground, and 2 unused (they are internally connected to each other with a green wire, this might have some use with the official Icom power supply, but i do not know.) I just put each of the 2 wires in 1...

This mount has holes to screw to the faceplate and then tabs to slide into the body of the radio in the same way the Icom one does. You will need 2 M2.6x5mm screws. The face sits centered on the body and flush with the bottom of it. Could be laid on...

This is part one of an adapter to replace the discontinued OPC 581/587 cable to enable remote use of the head on the Icom 706mk2g. It is far bulkier but allows the use of off the shelf parts to connect a SHEILDED network cable (not crossover) in...

I ordered a Diamond BNC to SMA adapter for my ICOM ID-52 and wasn't pleased with the gap in between the adapter and antenna base around the SMA post. This will perfectly fill the gap. I've provided 2 slightly differing files. 1 is a spacer that...

Stacking bracket for ICOM IC-7300/IC-9700 transceivers is a must-have for those who want to utilize the tilt foot on the lower radio and gain a bit more space between the units. This custom bracket (x4) offers the required stability and an additional...

This may fit other models as it was also tested on an Icom IC-F121s VHF radio. I used an Icom IC-F320s to measure the screw holes to mount it. It is intended to screw to the trunnion (Mounting bracket)holes. The F320/F320s and the F420/F420s...

Dock for the Icom IC-705 which includes space for the DigiPi. (Raspberry Pi Zero). Raspberry Pi Zero and 1.3 inch integrated 1.3" display. I have created 2 additional versions with more internal space for wiring, you might go for this version...

After crafting a sturdy stand/handler for my Kenwood TH-D74 Radio (item 2884874), fellow ham enthusiasts requested I create one for their Icom 51a. So, I designed this stand and, after several revisions, settled on the current version. Key features...

I simply added a front support with mounting holes to hold the metal baseplate for the Icom ID-5100 transceiver. The addition is a little rough around the edges, but, it works fine and isn't seen when the draw is in position. The draw space is...

The spacers let you use the original screws without worry of them going too far into the power supply enclosure.Fans used:Power supply - Noctua NF-P12 redux-1700 PWM x 1Amplifier section - Noctua NF-R8 redux-1800 PWM x 3Tuner - Noctua NF-A9x14 PWM x...

Like the D700 used to have, and like Icom mics use. I find it's a lot more versatile and easy to hang up when you're not looking.</p><p>This is an adapter that fits (tightly) on the back of a modern Kenwood (and maybe other brands) hand mic and...

Like the D700 used to have, and like Icom mics use. I find it's a lot more versatile and easy to hang up when you're not looking. This is an adapter that fits (tightly) on the back of a modern Kenwood (and maybe other brands) hand mic and provides...

ic7000 head unit rear dress cover for use with icom mount MB105, encloses the rear covering the ugly bits, the leading edge does sit proud, print it in black and it's hard to notice or sand it to lesson it. (once the unit was mounted in the vehicle...

Face protector I made for the ICOM IC-705.Provided STL with Callsign and also STL with blank screen.

Remixed ICOM IC-705 antenna bracket with N connector instead a BNC and made in one solid piece

Smiley Rubber Duck antennas when ordered with the "MX" connector work on just about every ICOM commercial portable radio. I think they're a great upgrade from the ICOM OEM antennas, especially the shorty's on the F1000 & F2000. ... This was actually...