icom 208h 3d models

I'm currently experimenting with my printer, and coincidentally, I needed a mic hanger for my Icom radio. ...My shelf was slightly thicker than intended, so I studied the original design and created a virtually identical one in TC - a project that...

Human: A six-contact power connector suitable for radios including the Icom IC-706, 707, 718, 720, 721, 723, 726, 729, 730, 735, 745, 737, 738, 740, 746, 751, 756, 820, 821, and 910 models. ...It is also compatible with the Kenwood TS-50, 120S, 130S,...

A "Handy Stand" for HTs is designed to accommodate a variety of handheld transceivers, including the TYT MD-390, Icom ID-51 & 31, and Yaesu VX5GR models. Its versatility makes it adaptable to most hand-held radios, with potential modifications...

The mount uses the ICOM in a remote mount configuration, where the radio base is remote (behind the back seat) to the front panel.The mount has provisions for a 1" ball RAM mount on each side. ... The following links are for other needed parts of the...

I use my Icom IC-7100 for portable HF, but I've struggled to secure my LDG IT-100 tuner to the radio body. These brackets attach to the radio body with M4 screws. The tuner floats between the brackets and I used a little adhesive backed felt to...

You can use it as external speaker for your radio like Motorola, ICOM, etc. There is M5 nut inside(for external holder), just put them inside to the holders and secure them with soldering iron or hot glue, etc. It can fir some small speakers, i...

I wanted to mount the remote head for my ICOM IC-2730a in my F-150 and created this bracket that slide into the driver side cubby. It stays pretty well in place once printed, but to insure it didn't slide out, I used some velcro underneath to secure...

You can use it as external speaker for your radio like Motorola, ICOM, etc. There is M5 nut inside(for external holder), just put them inside to the holders and secure them with soldering iron or hot glue, etc. It can fir some small speakers,...

This innovative mounting solution was initially engineered with the Icom 706MKII radio unit in mind, although it could be adapted to fit other brands' face plates by simply drilling new holes. ...The unique design feature allows for two components to be...

The mount, designed for attaching airband radios like the Icom A15 to paragliders, utilizes the radio's belt clip and attaches it to a 25mm tube. It's an improved version of a UHF radio mount, showcased on Thingiverse...

Swiveling folding tilt feet for the Icom IC-705. Uses existing screw holes but requires longer (3X16mm) screws. Includes a groove to snap on an O-ring around the circumference of the foot for better traction. Look in your local hardware store for...

The Orpela YB1 Is inspired by the Knight's horses dress,this inspiration icoming along the waist line of the Orpela, we gave it flow surfaces that make it be very dynamic and light. Those surfaces are contrast to the lower part of the car which is...

I liked the design by by badtime of a Stand for the Icom ID5100 with the angled display. (https://www.thingiverse.com/thing:1788573) but it was hard to impossible to print. Also, the two legs weren't the same size. So I duplicated one of the legs...

This is a 3-part print designed to mount an Icom VC-V8000 securely onto a 3D printed sled. The sled enables the radio to be placed atop a radio box, preventing it from sliding or falling off the back. The print consists of three distinct parts: the...

... are called "cup" I included some blank mounts that have 3 m6 holes in them so that you could mount whatever you wanted. The microphone slots accommodate most round style mounts. The ICOM mount accommodates most clip style mounts. ...

I took the only Icom ID51 mount on Thingiverse and blender'd it up with the RAM mount for GoPro thingi. I have also added the individual STL files for the Ram Mount Ball Hitch, the rear cone, and the holder. **v5: Parted out each component. Not a...

This text appears to be a project log for a custom radio communication device built using a PELI/PELICAN case, an Icom IC-7100 front panel, and various other components. The project is still in beta state and the author is inviting feedback and ideas...

Similar stands are also available here for the ICOM ID-51 and the Kenwood TH-D74. A slight improvement has been made to make the stand fit the radio a little better, also to match the designs for the ID-51 and TH-D74 stands. ...This was done on May...

... the slots on the battery and anchored by the belt clip, this design allows you to charge the radio while on the stand. Print with support recommended for a sturdy finish. Similar stands are also available for the Anytone 878 and ICOM ID-51.

MAGNADYNE RV73 AM/FM Recreational Rubber MAST Antenna with 3" MOUNTING Base and 96" Cable https://www.amazon.com/dp/B07P1Z89LK?psc=1&ref=ppx_yo2ov_dt_b_product_details Bingfu Mobile Ham Radio Antenna Dual Band VHF UHF 136-174MHz 400-520MHz Amateur...

I have included some pictures of the enclosure alone AND with the ICOM wedge/radio seated on top of it. I am including .stl files for three revisions of this enclosure. Here are the details for each:</p> <p>Revision 1c: This is the model represented...

I got the AL-705 ICOM labeled Magnetic Loop Antenna from Alpha-Antennas. Unfortunately it comes standard without a tripod mount option. You can get a adapter from alpha-Antenna, but its (IMHO) ridiculous expensive (~50$) and I couldn't find an...

These rails were designed to secure an LDG Z11 Pro II tuner to the body of an Icom IC-7100 for portable HF. This is a remake of my LDG IT-100 tuner backets. These brackets attach to the radio body with M4 screws. The tuner floats between the...

I designed this bracket to secure the detachable front panel of my Icom IC-706MkIIG Transceiver to the dashboard of my 2015 Jeep Wrangler. The bracket "clips" into the gap above the radio and then fits snugly into the pocket on top of the dash. I...

We designed this for the Icom ID-5100 radio, but you can easily customize it for most ham radios with similar shapes. To do this, measure the radio dimensions and the distance between screw holes using a ruler or calipers. With 3mm walls, prints made...

This mount is an innovative spin-off of my original UHF radio mount, designed specifically for ICOM A15 airband transceivers on Thingiverse (thing:283818). Due to its larger dimensions, the A15's belt clip provides better attachment, and the...

Very simple radio stand, perfect for most handheld radios including Baofeng, Kenwood, Yaesu, Icom, Anytone and many others. Just slide the clip over the top. v2 - Basic stand for smaller radios with standard antennas. v3 - I discovered that using a...

These rails are designed for mounting on the side of the IC-7200 HF radio from Icom, providing protection and ergonomic handles that make lifting a breeze. I've had my fair share of lifting this radio, and with these handles installed correctly, they...

I will be posting a similar holder designed specifically for Icom microphones soon. The modular design of my shelf allows me to easily rearrange compartments and secure them with locking brackets, providing versatility and convenience. For those...

I recently received a couple of nice VHF radios from Icom. I purchased battery packs online, but didn't have any charging accessories that normally come with these radios. This project prints a drop-in charging base that lets the radio be charged...