i3 mk2 5 3d models

Modified a bit for easier M4 nut insert. Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: No Supports: No Resolution: 0.2 Infill: 30% Filament: 3DXSTAT CF PETG Black Category: 3D Printer Parts

I struggled to discover a suitable raspberry pi camera mount arm for the Prusa i3 Mk2, Mk2.5 etc that functioned in tandem with the 'frog' and possessed sufficient clearance to clear the printer completely. This particular setup sits far enough back...

The Prusa i3 MK3/MK2.5 R3 update includes a nozzle fan holder, but there are several areas where it can be improved. Key Features: - A plug-in replacement for the standard holder is available. - The fan has a solid mount onto the holder using two...

The Prusa i3 MK3/MK2.5 R3 update comes with a nozzle fan holder, but it can be improved on several points.Features:Plugin replacement for standard holder.Uses two screws to give fan a solid mount onto the holder.No obstruction of airflow around...

THIS IS PART OF AN OVERALL Lack Enclosure design: https://www.thingiverse.com/thing:3129929 This is take two on the Original PRUSA i3 MK3/MK2.5 MMUv2 Backfeed situation for those that are having issues with alternate mounting as I was. This mount to...

The hotend fan cover is easily secured by snapping it directly onto the fan itself.

<p>Just a little remix to add an Imperial symbol to this fan cover.</p> Category: 3D Printer Accessories

I'm excited to share this upgraded Prusa MMU2 design for the "Pimp Your Prusa" contest! The main goal was to create an easy-to-maintain system that would eliminate dust buildup, gear grinding, and unwanted filament fragments from the pulley body. ...By...

A subtle tweak is added to give the fan cover a regal flair by incorporating the iconic Imperial crest.

<p>Just a little remix to add an Imperial symbol to this fan cover.</p> Category: 3D Printer Accessories

This will get everything in order. The holes that need to be drilled and the Bondtech extruder body require clearing out. I used a die grinder for this purpose. ...All bolts must be measured, and if any bolt doesn't fit through, drill a hole for it.

This sleek hotend fan cover simply clicks into place on top of the fan.

Just a little remix to add an Imperial symbol to this fan cover.

This hotend fan cover just snaps onto the fan.

<p>Just a little remix to add an Imperial symbol to this fan cover.</p> <h3>Print instructions</h3><p>Category: 3D Printer Accessories</p>

I remixed "Prusa i3 MK3 X-axis-cable holder R4 extruder for mk2,5 - add block for X endstop Remixed from: https://www.prusaprinters.org/prints/1995-prusa-i3-mk3-x-axis-cable-holder-r4-extruder Print instructionsPrint from PET, 20+% infil

I successfully upgraded my Prusa i3 MK2S to the MK2.5 by addressing a critical issue - lack of an ideal x-axis carriage that was compatible with my already installed Igus drylin RJ4JP-01-08 bearings. To overcome this hurdle, I relied on the remix...

When upgrading my Prusa i3-Mk2, featuring Igus linear bearings, to the i3-Mk2.5S, I discovered that the Igus drylin were not properly secured in the new X-carriage frame. As a direct result, any movement along the X-axis produced an annoying...

Direct replacement for original part.Makes it a lot easier to rewire a single wire without disconnecting all wires from the controller board.The older version for MK2/MK2.5 makes access to the X Belt without removing the back...

This modification is designed specifically for the mk2 full bear frame, adding MGN12C linear rails to the Y-axis. The files provided are printed parts needed to set the bed at its correct height. Note that you will require 6 low-profile countersunk...

mk8 extruder added to my prusa i3 mk2. Got tired of having to tear the whole printer apart in order to work on the hotend and extruder. This you take off the 5015 fan and two screws and the whole extruder can be pulled. Note that two threaded...

This is a remix from "PSU Replacing Frame Brace for Prusa i3 MK3" at https://www.thingiverse.com/thing:2859884 for Original Prusa mk2s/2.5 V1 This brace serves as a useful replacement for the PSU, allowing you to remove it from the printer if needed....

I was watching my printer and noticed how much the X axis is to Z at it adjusts automatically. Since I now have to change my thermistor, I decided to create feet for the frame to rest on while I tighten the mounting bolts to achieve a more squared...

Bearing holder for MK2s Category: 3D Printer Parts

Bearing holder for MK2s Category: 3D Printer Parts

I'm upgrading my Prusa i3 Mk2.5 to a full Bear (https://www.thingiverse.com/thing:2808408), and I quickly realized that I need to swap out the spool holder for one compatible with V-Slots. I use Masterspool reels featuring 608 bearings on an M8...

Whilst in the process of upgrading my Prusa i3 Mk2.5 to the full Bear (https://www.thingiverse.com/thing:2808408), I realised I needed to replace the spool holder with a V-Slot compatible one. I use Masterspool reels with 608 bearings on a M8 axle...

Works with Oakmountain's Bottom included in this remix. No modifications to heat bed/cables are needed to fit this cover on the heat bed with screw connectors. This has been tested on a heat bed with screw connectors. ... You will need: - Three M3x12...

In order to fix that, I completely remodeled the top half of the extruder body in Fusion360 (as I wasn't able to just move the filament path from Prusa's .step file).\r\nThese are drop-in parts for the Prusa i3 Mk3, and require no other changes other...

Modified the design slightly to make it easier to install an M4 nut.