hyperx quadcast mount adapter 3d models

SD card adapter mount Mount to hold an SD card adapter to the side of a 40x40 aluminum extrusion. Github | File | Description (assumes mounting on the right side of a rail) | | --- | --- | | sd_adapter_mount.stl | Orients the adapter vertically. | |...

Folding Bicycle Front Mount Adapter (Brompton Type) I designed these with Shapr3d on my Ipad. As I recently acquire a Brompton-like front mount adapter on folding bike. I took sometime to make sure it can carry loads with my other cargo adapters. It...

Designed exclusively for use with the bike mount of the Garmin GPSMap 60 Series, this adapter links directly to your bike mount and allows you to easily attach your GPS device to backpacks, belts, and more using a carabiner. Printable without support...

... similar mounting point. The total height is 150mm with a 6.2 hole to accept 1/4x20 threaded screw required to mount the binoculars to the adapter. ... I used 20% gyroid infill and printed with regular PLA, so far no rigidity issues observed.

Made this adapter after getting fed up with my phone constantly slipping out of its magnetic mount, utilizing the base of the Scosche Magic Mount and adding a couple of holes for secure bolting to my LG G6 mount's base using #6 nuts.

Adapting accessories from GoPro to replace a tripod mount is now possible with the new Backbone mod. This modification replaces the standard 1/4" BSW tripod mount with a GoPro camera fitting, secured by the existing Backbone screws. ...Originally...

The Smappee Mount Adapter is a versatile device designed to seamlessly integrate with your electrical panel by mounting directly onto it. This clever adapter serves as a crucial interface between the Smappee Monitor and your electrical system,...

This is an adapter that allows you to mount the MakerFocus Raspberry Pi camera (https://www.amazon.com/gp/product/B07DPNDP6R/) to Camera holder for Pi-Cam (https://www.thingiverse.com/thing:3315512)

A simple adapter mount to attach a ~57mm (2-1/4") adhesive furniture pad to to a 48mm foot leveler (from a Progressive standing desk). ...More information available on my blog Category: Household

This is and adapter that allows to use your standard 1.4" / 35 mm speaker pole stand. ...It was designed for JBL8340a, but it should be usable with all JBL cinema speakers using the same 4 screw mounting interface.

I required a method to secure my Bluetooth transmitter (MYCARBON Bluetooth Adapter) to my guitar amp, therefore I created a mount that safely secures the module alongside the amp, permitting easy access to all its input/output interfaces.

The following instructions are needed: print the board, mount four nylon standoffs (reusing most from previous setup) onto it, attach the adapter plate to your quadcopter, and finally secure the APM2 Purple to the adapter plate. ...After that, you're...

A simple mount to hold AC adapters since they don't fit in server rack cable organizers. Prevents the adapters hanging from their cables. Designed it to be screwed into the bottom of a desk with wood screws, but adhesive strips should also...

... The PC4 fitting provides an improved grip on Teflon tubes, preventing the extruders from being pushed out of their mount. ...Additionally, it eliminates axial play, unlike the adapter that comes with the extruder or at least the one I obtained.

This is a versatile adapter designed specifically for mounting a Caddx Tarsier in a Standard 5 inch frame. It also seamlessly accommodates any other microcamera, allowing for effortless integration. ...The adapter expands the width of the camera from...

A bowden groove mount adapter fits snugly around a 4mm PTFE tube inserted into the intake hole, ensuring a secure connection. To prevent potential issues, note that the inner diameter of the adapter may decrease slightly during printing, so adjust...

... more updates. ... This is an adapter for the Amscope SAW single-arm microscope stand, for the Hayear 14MP C mount lens. ... Basically, it adapts the approximately 3-inch diameter hole from the stand to the 2-inch diameter hole for the microscope lens.

This adapter converts from that sliding mount to a ball joint type mount. Updated - Added OBJ with the screw adapter instead of the ball. The ball would break off after a month or two of use. The new screw adapter holds up much better to daily...

This adapter enables you to utilize both side mount and top mount plates for Berkley rod holders on a Crestliner CR1032 or any other aluminum jon boat in the Crestliner CR series. ...It may also work with Scotty rod holders, but since I only have...

A simple adapter mount to attach a ~57mm (2-1/4") adhesive furniture pad to to a 48mm foot leveler (from a Progressive standing desk). ... [More information available on my...

this is an adapter so that you can use both the side mount and top mount plates for the berkley rod holders on a crestliner cr1032 or any other of the crestliner cr series alluminum jon boats this may also work with scotty rod holders as well but...

My connector from the vent mount and the GPS mount broke after about 3 years of use. My first print left the ball a little oval shaped, but it still fits just as well as the original. This used the T-Notch adapter made by PocketBrain. ...it can be...

I replaced the phone mount that didn't work with my handlebar setup, a Giant Defy Advanced Pro, so I built an adapter to sit on top of the stem. ...It now supports both orientations of the phone mount seamlessly, thanks to a strip of cable-wrap velcro...

M42x1 CS-Mount Adapter, usable to connect old M42 camera lenses to CS-mount camera.Designed to match correct focal distance between lens and camera sensor.Technical details:https://en.wikipedia.org/wiki/Flange_focal_distance

This is a precision-engineered propeller motor mount adapter, designed with a meticulous 12mm spacing for optimal compatibility with standard M2 screws. To assemble the adapter, first print the object using your preferred 3D printer settings, then...

I'm working on an adapter mount for a Kidde smoke detector to secure it firmly to a ceiling mount. However, upon inspection, I found that the holes provided were too small for the screws I had chosen to use, necessitating some drilling to bring them...

These home theater speakers are made to mount flat on the wall so I made this adapter to fit on this ( https://www.thingiverse.com/thing:2104478) using ½ screw and nut and I can adjust the angle of them. But they can be adapted to more mounts. ...

This is a groove mount adapter that fits into the Titan extruder to mount it to a CR10 V2 or V3 The threaded bit is an M10x1 that is 8mm long It screws right into the top of the hot end to mount a titan extruder Print with at least 0.15mm layer...

This is a groove mount adapter that fits into the Titan extruder to mount it to a CR10 V2 or V3 The threaded bit is an M10x1 that is 8mm long It screws right into the top of the hot end to mount a titan extruder Print with at least 0.15mm layer...

This is a small bracket to mount the rather chunky CAC-1010-A Active DisplayPort to Dual link DVI-D adapter from Club3d. I used it to mount the adapter to the back of my desk to alleviate strain on the cables and make things a bit tidier. The...