hypercube 3d printer

  A bit of extra info: Customizer is based on OpenSCAD, a program that can generate 3D models out of a set of instructions. A customizer file is just a .scad file with specific formatting. You can use any version of OpenSCAD to load and edit a...

Hello !Wellcome to my little office with Prusa MINI +.I made industrial lamp with concrete base, retro bulb and soft pad made of recycled rubber.O.10 DETAILPrusament PLANo supports15%We will need: Concrete (fine concrete with small...

Description: A set of 3d printable parts to compactly combine two LRS-350 PSUs into a compact unit with optional voltage and current displays. I put this device together so i could consolidate the 10+ individual power bricks for each compute node in...

* Once assembled my new FelFil extruder (https://cults3d.com/en/3d-model/tool/felfil-evo-extruder-case) I began to design a cheap and affordable spool winder; I had to design a cooler for extruded filament and a digital sensor for filament diameter.

one solution would be my 70mm clamp: https://cults3d.com/en/3d-model/tool/70mm-clamp-with-beam-support-for-anamorphic-projection-lenses ADDITIONAL PARTS Some additional parts are needed for this QR clamp Step-up ring to 77mm (the common cheap ones;...

PLA has an inherent shrinkage factor, and that varies depending the type of PLA you use and all the other many things that go into 3D printing. You may need to adjust your slicer to (every so slightly) enlarge or shrink the part. Z-axis dimensions...

ESP32 DevKitC (v1 or v4 tested)...

I commonly start plants in an Aerogarden and then once the seedling grows a long enough set of roots, I move it into this bin system.Check out my 3D printed Aerogarden pod design here: https://www.thingiverse.com/thing:4560879Check out my video about...

The field is confined by a steel “yoke” that forms the bulk of the detector’s 14,000-tonne weight.CMS acts as a giant, high-speed camera, taking 3D “photographs” of particle collisions from all directions up to 40 million times each second. Although...

So to keep it simple, here is a parts list:3D Print:1x Nose Cone1x Bodytube*1x Stage 2 fincan**3x Stage 2 fins (small fins)***1x Stage 1 fincan**3x Stage 1 fins (big fins)****Print in Vase Mode with one layer walls, at 0.45mm**10% infill***100%...

Think of it as the gauntlet is laid down and a super fun challenge in 3d spatial orientation! Oh and don't superglue your fingers, eyelids, or other body parts to various things, it's not as fun as it sounds. You may want to try using sticky tape...

The alternate roof is 2 separate 3D print, use the layer change details above to get correct colours. ###Step 4: Exterior & Interior Props (Optional) All the exterior and interior props are optional. The parts found in both folder are simple...

#### Now you can examine and download the right parts from [here](https://www.myminifactory.com/object/3d-print-79629) My Old publication (this is a replica) had: 35191 views 10941 downloads 738 likes 936 collects 24 watches 185 comments 17 makes 17...

Join our Tribe or Patreon to receive amazing 3D printable miniatures set each month for a very special price!  Save big on the complete Bronzeclad Greatgoblins bundle, which also contains pre-supported files for each STL. Please check the images to...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

In this case my 3D-printed adapter is a simple 65 mm tube of suitable outer diameter. Other LED flashlights have a contact spring at the positive terminal (usually located towards the LED) or even at both ends (LED side and end cap side). In this...

I give you the 3D printed Sterling main spring forming tool...https://i.imgur.com/j04a7Tb.jpgIt is simply a grooved shaft set to the correct diameter and pitch of a Sterling main spring. The shaft is hollow, allowing you to slip it over a section of...

This push-to release mount for the Google Chromecast TV remote, stores the remote under a coffee table, and a simple push on it's obscured base, and it ejects the remote for easy access like this:As well as being a cool way to keep your able that...

Make your own custom chips.Accessories DescriptionImageFCS Label Mounting SolutionUse this to label what filament is stored in your dry box, Ikea samla or where ever else you want to label filament.FCS Label StandUse this to see what material...

Send me a message if you have a particular chess set design that you would like to see as a 3D model. I am always open to new ideas. Although I have steered clear of the Staunton design, I am considering adding the more popular formats, like the 1959...

... the Fine tuning adapter / rod holder. NOTE: Some more of my other designs: https://www.thingiverse.com/leadingedge/designs Best All-round 3D Printable Knife and scissors sharpener with lots of attachments: https://www.thingiverse.com/thing:4135236

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. ...Scan the World is...

The device was developed in response to the need of a more precise and functional 3D printed prosthetic option for youth performing every day activities. Link to...

Cómo configurar los parámetros para personalizar la impresión del puntero para teclear 2.1. Para poder personalizar el puntero para teclear deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de un software libre y...

DBA 3D Gloop! makes no representations on behalf of Valve Corporation or any of its subsidiaries. The content published herein are presumed adaptations of the original copyright holder and are provided to the public under Section 107 of the Copyright...

Make your own custom chips. Accessories DescriptionImageFCS Label Mounting SolutionUse this to label what filament is stored in your dry box, Ikea samla or where ever else you want to label filament.FCS Label StandUse this to see what...

... Base for your Walkers – Classic scale 28mm for tabletop wargames. ...3D format: STL file Don't need supports (you'll receive both versions supported and not) - The files are for personal use only. ...Do not copy or redistribute work (please contact me)

*Tubing* In addition to the 3D printed parts, this thing also uses steel tubing * Beam: 1" OD x 11" long * Column: 1.5" OD x 20" long The material I used was 18 gage. Any thickness will probably work but lighter is better. Maybe. *Steel Plate* ...

There are configurable-text-based creations, multi-line label, gadget display stand, sweeping name plate, bunting banner, customizable text box III, pyramid text, name plate, Customizable text box with lid and round text. Have also a look at my...

Join our Tribe or Patreon to receive amazing 3d printable miniatures set each month for a very special price!www.patreon.com/ArtisanGuildwww.myminifactory.com/users/Artisan_Guild?show=tribe Save big on the complete City of Intrigue bundle, wich...