hyper 212 am4 backplate 3d models

I spent some time making sure that with this mounting I was able to keep the BLTouch in it's original position mounted directly to the backplate and close to the nozzle. Most other designs with dual cooling fans move the Touch over 50mm away from...

... fit is loose. This conversion pairs nicely with this backplate for 80mm fans: http://www.thingiverse.com/thing:2137022 Post-Printing Tip! ...- Pull the little heatsinks off on your Melzi board and place them on the Ramps board's stepper drivers.

I also put here the other two pieces you will need, the focus ring and the backplate, but I will apreciate if you can go on the original model link and also thank him for the original model! Let me know if you like it, if you print one yourself...

UPDATE : 28/02/2021 Uploaded a new version of both sound wave pendants with a backplate for easier print removal with less likelihood of part damge, also uploaded more images of the pendants. Print Settings Printer...

The Chain mounting Plate that TNS designed was screwed onto the normal Carriage Backplate and was blocking the spot for the ABL-Sensor. The ABL-Sensor was too long and wouldn't fit... So Chain or ABL - Your choice! "Dang it, I want BOTH!!" So: Get...

The Ramps-FD box backplate with a 40mm fan was added for those who use 40mm fans. A new thicker-walled Ramps-FD box has also been created to help those who have trouble printing the original one. This is version 1 of my Ramps-FD enclosure,...

### Some Abbreviations * h: height * w: width * t: thickness * r: radius * d: diameter * l: length ## Parameters * Plates - `t_back_plate`: Thickness of the back plate - `h_back_plate`: Height of the back plate - `t_bottom`: Thickness of the bottom...

(bigger hole under GRIP mode will help you to insert earphone or charger) Printer SettingPrinter : Artillery Hornet0.12mm   , 0.2mm   both work, ( I recomend 0.12)no SupportPLA 2022-11-18Ver.2 released 2022-11-19reduce the...

3_Units_wave_1.1: I upped the resolution on the part because the wavy pattern in the backplate came out stepped. 1_Unit_max_size_roofed_1.1: Same here; the rounded sides of the part were stepped, so I upped the resolution here as well. Basic...

Backplate with M2 bolts recessed inside. Added holes inside the front case for m2 bolts. Some other minor changes. Motor skids made to take M3x10 bolts 4.5mm in the skid + 4mm arm and 1.5mm goes in the motor. I flown it indoor a little. Visually...

(2) Base (3) Backplate (4) Frontplate (for Pi Shield) (5) Object Holder in different sizes you might need to use a 5mm drill bit to widen the hole a bit. The number indicates the object size which can be scanned with this holder (a) 3cm, (b) 5cm,...

(However this will work with any creality ender style printer.) The idea behind this was to make the most compact and lightest way of mounting the orbiter, two fans (one 5015, one 4010/4020), the fan shroud, bltouch and the trianglelabs dragon hotend...

Backplate I wanted all the connections on the rear of the device. Here we have the Raspi connectors bottom right, power socket bottom left. As this setup is all 5V, I chose a micro-USB power input. The official Raspberry Pi PSU works well. Along...

... You can find the other two pieces, the focus ring and backplate, on the original model link in my "Remixed from" section. I don't want to reupload them, as it would reduce the visibility of the original model's creator. So be sure to check it out!

Noticed nut pocket for fan shroud on 26mm stepper backplate may not be deep enough for average M4 nut, replaced with modeled M4 thread to save space. 3. Added photos of first test prints in PETG. #####Update April 4 Part 2: 1. Uploaded new back...

... Use this design as a frame for another pistol. The only part of this holster which is Ruger EC9S specific is the housing which the pistol rests in. Maybe the backplate as well depending on the model. ...For a $10 tip, I could make one for you.

Anycubic PhotonS Air Filter - for the 2nd generation Anycubic Photon: Unlike the original Photon, the PhotonS does not have a backplate which can be replaced. I initially planned to use a flat adapter piece and stick it to the back with double-sided...

... block. Additionally, I tweaked some clearances to minimize escaping air even further. These make installation harder - it looks like the holes don't fit but that's intentional, so you have to use some pressure against the backplate for mounting.

BOM: a 1.2" 7-segment display from Adafruit in whatever color you want a Raspberry Pi Zero and supported power chord some female to female jumper wires a small wifi dongle, preferably one that you don't have to compile the module for (ahem) (for the...

Shifters: I've modified these ones https://www.thingiverse.com/thing:3468245 to provide a physical endstop, utilise 10x10mm magnets & provide a different shift paddle - https://www.thingiverse.com/thing:4590694 BOM: 2x 2.5mmx12mm (for multi-switch...

UPDATE TIME I have created and back plate to now mount this to the ENDER 5 / 5 PLUS Microswiss DD backplate! i have made it so that it still fits the StealthBurner part that i modified and is included in the downloads. the only thing i had to move...

(2) Base (3) Backplate (4) Frontplate (for Pi Shield) (5) Object Holder in different sizes you might need to use a 5mm drill bit to widen the hole a bit. The number indicates the object size which can be scanned with this holder (a) 3cm, (b) 5cm,...

Bond backplate and grip assembly using acetone or other adhesives; verify firing pin moves freely before permanently bonding surfaces together; ensure top, bottom, and sides align properly (use square ruler to verify edges are smooth and aligned...

If you don't want to (or cannot) use your original hardware - I've included capture cutouts for m2 nuts in the backplate, so you can use an m2x6 inserted from the top to accomplish the same thing as the original fastening arrangement. If you use...

3 round 5x3 neodenium magnets go in the 3 holes in the back of the tool backplate. The lock shaft needs a pair of holes drilled in it to slide a 1.5mm pin into place and to screw it to the gear (but glue might work on this. The pin doesn't have to...

There are a few other things that need perfecting , I shall update as I progress. Things which need improving. Rear IO panel needs slight adjustment ( adjustment already made but not tested yet) Mount for 2.5" HDD or SSD. Fixing method for GPU...

It was also my first large-scale project, so tolerances aren't 100% tuned in yet.Print at your own risk (of filament)! A better (fully parametric) version of this frame is coming..2mm layer height is recommended for this projectthicker walls will...

Additionally to the 3D-printed parts you will need: 12x Cherry MX switches (I chose red ones - https://www.reichelt.de/cherry-mx-red-tastenmodul-schnappbefestigung-cherry-mx1a-l1nn-p202567.html?&trstct=pos_10&nbc=1) Cables for wiring Solder Arduino...

(Not compatible with V6 hot end, due to the supporting backplate) This model has been tested for 6 months on the Ender 5 Plus, this version is working stable and sustaining high-end temperatures. The aim was to make these “STL” files easy to...

The backplate which mounts on the carriage I printed at 100% infill and several walls thick. The bigger part for the mount I did 60% infill, but still pretty solid due to several walls.I also used PETG due to the durability over time, plus higher...