hydroflask bike holder 3d models

this is a simple holder that attaches to a stationary bite so that you can not worry about your Samsung remote falling down

This holder exploits the undercuts at the back end of the SPD cleats to keep them firmly in place on the wall.

Bicycle pump holder, a self-adhesive foam must be added to the inside to prevent the pump from slipping. ... Version 2 has been reinforced

This is a straightforward bottle holder designed for bicycles, capable of being printed in multiple parts without any necessary support structures. ...It's suitable for most bottles.

created this as an assignment for an engineering design class comment suggestions for other versions of a business card holder (i.e rocket, computer, logo, etc.) Category: Office

Bike handlebar diameter: 28 mm Hardware List: 4 - M3 x 15 mm screws; 2 - M3 x 25 mm screws; 1 - M3 x 20 mm screw; 4 - M3 x 15 mm screws with countersunk heads; 14 - M3 washers; 11 - M3 hex nuts. Insert a small piece of EVA, 1.5 mm thick, between...

English : I created this bike anti-theft mount that attaches to the seat tube. The fixing diameter of the seat tube is 28 mm. The diameter of the lock body passage is 22.8 mm. The diameter of the passage of the cable end of the lock is 14.5 mm.

English : I created this bike anti-theft mount that attaches to the seat tube. The fixing diameter of the seat tube is 28 mm. The diameter of the lock body passage is 22.8 mm. The diameter of the passage of the cable end of the lock is 14.5 mm. You...

This is a universal phone bike mount. You need a long (40-45mm) bolt M3 where I melted a knob on for better control. I melted a M3 insert for the bolt. The mount fits handlebar diameter 32mm with M4-bolts The b-version is without phone...

Want to ride your stationary bike while taking part in all those unfulfilling zoom meetings? I do! But, I don't have a good place to put my laptop so I can see what people are presenting.\r\n These clamps hold your MacBook Pro (13" or 15") right...

Simple holder for phone. ...Not tested, will print tomorrow. For me it is important to have thick enough holder to keep phone without taking out from case. ... You will need 2 8mm rods/alloy pipes and spring or rubbers to build holding force.

But here's the thing - my new tail light holder also broke apart after printing! What's going on?! So, I decided to take matters into my own hands and design an even stronger one. Don't worry about it being in two parts - just print the whole thing...

A simple rear reflector holder attached to a mudguard using two M4 screws. ... Print Details Printer Manufacturer: RepRap Specific Printer Model: Prusa i3 Raft Generation: None Required Support Material Generation: Not Necessary Layer Height: 0.2...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/fwx8JlCiatU Bicycle mug holder especially for Stanley Traveler Mug. Only fits to old style 25.4mm handle bars. ... Install as close as to the quill/stem.

Helmet holder. The middle part (metallic) is 20mm * 20mm * 2mm aluminum (30cm long) extrusion from shop near by. Material is PLA. ...Fit is tight but with a bit of wigling you can assemble it.

To fit on a spare bottle mount, this is a holder for small bananas that I designed as a bit of fun for a cycling group gift exchange. It was made from PLA and coated with paint to resist UV damage. Not that I think anyone will use it seriously. ...Too...

Here are the GoPro holder connectors: http://www.thingiverse.com/thing:1488168 http://www.thingiverse.com/thing:1696877 http://www.thingiverse.com/thing:37761 http://www.thingiverse.com/thing:361198 Print Settings: Rafts: Don't bother Supports: Yes,...

Simple little design that has a right and left hand 9/16-20 thread that allows you to keep bike pedals together when you're storing them.  Just like most pedals, the left side has ribs so you can easily tell which side is which, but there are also...

Keep in mind that bike locks and frames can vary significantly in design, so it may be necessary to make adjustments to this model (available as a Blender file attachment) for optimal compatibility. **Print Settings:** * Printer: Rigidbot * Rafts:...

This new project has been created to realize an easily mountable smartphone or GPS navigator support for the handlebars of any mountain bike or bicycle. Thanks to its 31.8 mm diameter fastening, the support can be mounted on most standard handlebars...

This new project has been designed to make it easy to attach a smartphone or GPS navigator to the handlebars of any mountain bike or bicycle. The support can be mounted on most standard handlebars available in the market, both horizontally and...

#The Bottle Holder There are plenty of bottle holders and plenty of them work fine, but they also tend to be quite thin. This works fine for printing them, but the bottle holder will be fragile and might break after hitting a small obstacle, like...

Other potential versions of the business card holder could incorporate various themes, such as: A High-Tech Computer: Imagine a business card holder designed to resemble a miniature computer, complete with intricate details and a touch-sensitive...

Since the initial circle didn't provide sufficient room for my mug, I disconnected it from the handlebar holder and created a brand new circle. With an interior diameter measuring 3 inches, this circular component is a straight design, deviating from...

To create this makeshift phone holder, I attached the inner tube rubber to a sturdy mount, ensuring a snug and secure fit that can withstand rough riding conditions. ...To guarantee a seamless connection, I applied a small amount of glue to the rubber...

This is a custom design for a Pixel 2 XL Phone holder, complete with a case attachment. The Fusion file is available for editing on Thingiverse at https://www.thingiverse.com/thing:4592416. To assemble this device, simply attach it to your phone...

The width of this holder has been tailored to fit snugly around my iPhone 8 plus case, but feel free to adjust it according to the size of your device. To assemble this product, simply follow these easy-to-understand instructions and attach all...

I remixed this design from https://www.thingiverse.com/thing:2357507 and modified it to remove the battery holder, swapping the phone dimms for ones that fit my iPhoneX with its protective case snugly. I hope this revised version helps someone out...

... in a gap between a closet and the wall. ...Because of its tall shape we were afraid it might fall over and damage itself or the wooden floor. The little foldable holder prevents that. We attached it to the closet with removeable adhesive tape. ...

Taillight holder (Replacement) Mine has broken. So I've printed a new one from https://www.thingiverse.com/thing:3473962 But it also has broken! So I designed a new one but stronger. 1 File print, but it´s divided into 2 parts. You can break apart...