hummer ev 3d model

I recommend 3 loops since this is quite a small model. Otherwise not enough PETG is dumped before the start of the parts</p><p>Print bed recommendation: Powder coated steel sheet with glue stick. I usually just put a 5cm to 10cm light line on the...

If you still want to print your own loc line, I used the models from [MinyMan644](https://www.thingiverse.com/MinyMan644) found here -> [Loc-Line Fittings (1/4", 1/2" and 3/4")](https://www.thingiverse.com/thing:3268462). I strongly recommend...

The models in my pictures were printed in beige ABS, which is a standard 1.75 mm filament from XYZ manufacturer. I have not tested other filament materials with this design. If printing as a fake sprinkler, I would recommend choosing black; bright...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

It does not matter which direction is taken.Continue running the line down and up between the pieces through different holes until it is fully connected.The line must turn a corner on the bottom piece, so ensure that it is placed completely in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 7 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

Many thanks to Dalek_Kolt for providing the original model, you can find more ripped stuff from them here: https://www.vg-resource.com/thread-39778.htmlDisclaimer:The figure you see in the photos is a larger version that houses LEDs and batteries. If...

The battery negative is connected straight to the Anderson PowerPole negative and the radio negative.The model includes a plate to put on top of the batteries to ensure nothing gets in and shorts them out.To make the antenna fit inside the box with...

This is definitely WIP, I do not own a Orbiter V2 and the design is derived from the CAD models. Update:18\10\21 Uploaded some 5010 fan ducts which are 8.5mm longer to allow for a Volcano Hot End. These are definitely WIP. I have not printed,...

the tabs are at different positions on each model. * Group Token Holder - slots in behind the main card holder. * Player Holder - holds the large Agent Pawns. * Player Tray Base x 4 - print these in the 4 player colors. * Player Tray Top x 4 -...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Merry Christmas! You will need to print: 4 ea Whirligig blades 3 ea Eccentric cams 2 ea Crossbars 2 Reindeer 2 ea Base Couplers 1 ea all other parts There is a cutaway view in the thing files called cutaway view.pdf showing how the model goes...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

In order to stay within bed size, put your skirt 0mm to the model. Once printed, remove the support material and clean up with sandpaper. Step 2: Print 2 Simple Metal Spool axle holders, same Splic3r settings as above. You can print both of them on...

Project: Playdough Tool Design Challenge Overview & Background: Through this lesson, students as young as five years old can be introduced to 3-D modeling and desktop fabrication, with an emphasis on its ability to provide solutions to everyday...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

If you want to save time while testing, you can print the included calibration test instead of the full model, but that is optional.Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It may feel...

More information: The models were printed in PetG and have a consumption between 5.7g and 7.0g and the printing times range from 0:47 to 1:15 hour. Note1: If the z selection alignment is used, you can generate a line as the one shown in the...

**HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE** -------------------------------------------------------------------------------------- Here are the two videos that give details on how I print much faster with stock hardware (changes to slicer...

My goal was to make as many of the modifications as possible to be 3D printed parts.Note that in addition to the .STL files, the Fusion 360 file containing all these parts is also provided. Some parts need to be rotated after importing into the...

:D This is a "small" and simple attempt to build a 3d printer. Small and simple are the keywords here. Just some basic parts to print, standard components you can get anywhere and no special and expensive tools required, as I don´t have access to a...

3D Printing: The Morse writer telegraph consists of many printed parts that are assembled together. Some of them could have been printed as a single piece. However, I avoided doing so to keep the printing times manageable. Additionally, this allows...

Basic profile: 25% infill, 4 walls, ironing top layers, ...Note: the included images illustrate the goals of the steps outlined below.[ ] 3D Print included stl files[ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan...

An O-ring was added as a countermeasure.シロッコファンと「fan adapter」の間に隙間が空いていました。シロッコファンの四隅のうち一つには固定用の穴が空いていないため、三点固定になってしまいます。このため均等に力を加えるのが難しくなっています。対策としてOリングを追加しました。The updated models are "fan adapter" and "fan connecter".アップデートしたモデルは「fan adapter」と「fan...

The only sound comes from the layer fan.I have included the STEP files to facilitate remixes and alternative configurations.An associated BMG type extruder/carriage can be found here:...

When I saw the Safe box from Hugo this inspired me to do my own Safe (or Lock).This is not a remix. I modeled everything in CAD from the scratch. But i printed Hugo's version before and &nbsp;had a look at it. I recognized parts which he designed...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press fit...