hpi rs4 3d models

It is a wishbone for an old HPI RS4. ...Part number for the complete suspension arm set "A450" from HPI Racing Es ist ein Querlenker für einen alten HPI RS4. ...Teilenummer für das komplette Querlenkerset "A450" von HPI Racing

Air intake pipe modification for HPI RS4 3 Drift nitro car involves reversing factory fitted rubber pipe bend, pointing it forward and cutting a hole in the hood matching air filter diameter. K&N breather filter is recommended with air filter oil to...

Lipo Battery Mount for HPI's Popular RS4 Sport RC Car, Perfectly Scaled for 1/10 Scale Models

... they don't get in the belt. Parts are likely able to fit other HPI vehicles, I found the lower control arms for my Rally appear to be close enough to the standard RS4 that the ones from this page will work: https://www.thingiverse.com/thing:4655433

This is a custom replacement spur gear for the HPI RS4 Evo3+, its part number being 47T (HPI 76817). It may also fit other RS4 models. Unfortunately, I couldn't find any online retailers that sell this component, so I decided to print it myself using...

Front body mount for a HPI RS4 Sport 3 havent printed this yet so might be an issue I havent noticed

Replacement upper Suspension support arms for the HPI RS4 3 evo+ (might fit other rs4's.) I decided to make thicker custom ones rather than design an exact copy of the originals from the car. You can view/download the Fusion 360 project here.

Replacement upper Suspension support arms for the HPI RS4 3 evo+ (might fit other rs4's.) I decided to make thicker custom ones rather than design an exact copy of the originals from the car. You can view/download the Fusion 360 project here.

Replacement upper Suspension support arms for the HPI RS4 3 evo+ (may fit other rs4 models too). I opted to design thicker custom versions rather than replicate the original parts from the car precisely. You can view or download the Fusion 360...

A motor mount for the HPI RS4 Sport 3 will require the 3 holes drilling and tapping to M3 that attach it to the chassis the bolts for adjusting the motor mesh are accessible through the suspension with a narrow long screwdriver the only downsides are...

I was looking for a new spurgear for my HPI RS4 (single gear) but since the parts are not made anymore and my got ripped of all its tooth i designed a new one. i do recommend using supports. Recommend ABS becouse it can "bend some more" ...

These are 3D models of all of the plastic parts found on the original HPI Nitro RS4. Most of these pieces can be used as direct drop-in replacements for the factory originals. All hinge pin holes should be reamed out with a 3mm reamer and all...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/fDybLzWuUAh

Repaired my HPI RS4 Evo nitro 1/10 RC car's broken control arm by designing a replacement using Inventor. Printed the model and successfully installed it, ensuring optimal performance. ...Say goodbye to long waits for hard-to-find replacement parts –...

The Vintage HPI RS4 Nitro MT features a removable radio tray, secured by specific components. A tiny round pivot at the back of the center tray serves as one crucial part. Two flanged body mount pieces are also required to keep it in place. These...

This is a remix of a Lipo Holder for an HPI RS4 Sport (a vintage 1st Gen version). This has been modified to add a small pulley to slightly raise the belt off of the LiPo case. Otherwise they would lightly rub so this hopefully prevents belt wear. ...

People who build RC cars will find that 2 wings and a diffuser make a great modification for their HPI Micro RS4. They can fit the diffuser on an R34 body by using some special adhesive called "amazing goop" which is also known as "shoe goo". To...

Replacement Throttle Linkage for a HPI RS4s Nitro Star G3.0 Engine. I highly recommend printing this edge down with supports as shown to prevent layer lines from running horizontally across the neck of the part. **WARNING**: PLA may not withstand...

Replacement Throttle Linkage for a HPI RS4s Nitro Star G3.0 engine. I recommend printing this edge down with supports as shown to avoid layer lines going horizontally across the neck of the part.</p><p><strong>WARNING</strong> <strong>THIS...

<p>Are you looking for a sub $20 mod to bring life back to an old brushed on road rc car and make even a driveway difficult and a challenge to drive? ...Then your in luck</p> <p>This fits 6mm body posts with 65mm spacing</p> <p>Runs off the servo output...

Want a sub $20 upgrade to breathe new life into an old brushed on-road RC car and make navigating a driveway a thrilling challenge? You're in luck. This upgrade fits 6mm body posts with a generous 65mm spacing. ...It runs seamlessly off the servo...

Are you looking for a sub $20 mod to bring life back to an old brushed on road rc car and make even a driveway difficult and a challenge to drive? ...Then your in luck This fits 6mm body posts with 65mm spacing Runs off the servo output of a rx channel...

Crafted specifically for the HPI RS4 Evo, this component can also be adapted to other models. To install it, you need to drill your own mounting holes. It reuses the spring lid from the original tank and incorporates baffles to prevent fuel sloshing...

Replace the worn-out front tire of your Micro RS4 with a brand new front drift tire. ...Simply swap out the old rubber for this high-performance replacement.

Replace the worn-out rubber tire on your Micro RS4 car with a brand new rear drift tire to enhance its performance and handling. ...Simply swap out the old tire for this replacement part to get back on the track in no time.

Repaired the front bumper's mounting component, which supports the foam part, in Inventor software. The revised design is even better than before and has slightly increased thickness to prevent cracks. ...For optimal strength, use a 100% infill.

This is a replacement wing mount for a drift AE86 body for Micro RS4 from HPI. The original design requires you to bend the piece, so it's prone to break there. It seems the official replacement part is HPI #73405, which would comes with 3...

These are head- and rear light buckets designed specifically for the micro-RS4 Ford Mustang model from HPI, a miniature replica of Justin Pawlak's formula drift car featuring Falken Tire livery. The buckets utilize 4mm square white LED SMD chips to...

WIP this does not fit original tires, this is completely independent! ... tires: tpu wheels: petg

Are you having difficulty fitting an aftermarket intake onto the small lip of your compact carburetor? Is it challenging to secure it due to adjustment screws in the way? Try using this intake barb fitting, which can be easily attached with a minimal...