hp server power supply 3d models

This is a bracket to mount two HP server power supplies into a BTC-S37 mining case.

... ops. ...73 Paulo G0MUW, CT1EFL, F5VMJ Full build details on my Hackster account: https://www.hackster.io/pnjorge/hp-server-power-supply-case-64f438 Videos: https://youtu.be/KsLedhMzRkY https://youtu.be/M5qRzoQIgcs https://youtu.be/q8ZGHTefn3o

Was making a 2nd 3D printer and wanted to use a Server power supply as it was cheap and very durable. ... Wanted to make a Shell to help Case it with Arduino Ramps 1.4 All measurements are as close to the real thing, Considering 0.1mm differences in...

Many people use the high-density hp server power supplies in the exterior christmas led lighting boxes. ... These models (2 pairs required per PS) allows you to mount them vertically inside a box (will mount in CG1500) using (4) ¼-20 bolts or...

This should attach to the back of an HP server power supply like HSTNS-PL11 1200w and allow the power supply exhaust to exit while pulling in fresh air around it or from another opening. Scale to .5 for creality ender 3 I've included the blend...

HP server power supply edge connector protector. <b>For personal use only.</b> <b>Attribution</b> — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but...

HP server power supply edge connector protector. For personal use only. Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that...

A replacement handle for an HP HSTNS-PR17 server power supply. ...(AKA the power supply for a HP DL360 G6, but should also fit similar models like the DL380 G6)

A clamp down mount for the HP 750/1200w power supplies. Print two sets. Holes for the clamp are printed to be tapped using a 1/4" tap. ... Use 1/4" machine screws to tighten the top clamp onto the bottom mounting plate.

Remixed front panel from https://www.thingiverse.com/thing:4947889 to allow for small metal SPST On/Off switch. ... Thanks to pnjorge for a great design!

These are HP server power supply mounts. ... I use them with M3 bolts

When used in combination with my existing [HP power supply mount](https://www.thingiverse.com/thing:4605175), adds a second HP power supply mounted above one mounted on the lower one.

Bracket designed to hold an HP power supply with a wizard of wire breakout board, a Falcon Smart Remote, and a JBoards Power distro-8. All in a Harbor Freight .50 cal ammo box. Designed to print without any supports needed, you may get a little...

for those making a 24v power supply here is a mounting system that is easy to print. ... the front and cover are designed to print with no supports the back only needs supports for the stop points.

These are HP server power supply mounts. I use them with M3 bolts Category: DIY

This bracket is used to mount an HP server power supply to the bottom of an Ord Bot. The power supply I used is a 750 watt supply part number HSTNS-PL18, but I believe the more popular 1200 watt supply may share the same dimensions and fit as well.

his is a bracket for mounting an HP Server Power Supply into a Bud Industries NBF-32022 enclosure. It uses two of the same 3D Prints mounted "facing each other". The bracket fits the HP 1200W/750W power supplies sitting in opposite directions, held...

Simple cover for the exposed power connections for the HP server power supply (750W) that is commonly modified for RC charger usage. Provides separation of the + / - sides, and makes for a clean look. ... I attach this with a bit of "goo" type...

This is a server supply holder for 2020 alumium profile.

Hakko T-12 soldering station mount for HP-460 server power supply upd. ...29.01.19 Fixed dimentions

General dimensions for the HP DPS-600PB Server Power Supply are as follows: Height is approximately 1.75 inches, Width measures around 6.48 inches, and Depth is about 5.92 inches. ...This information can be beneficial when planning for space constraints...

Remixed from https://www.thingiverse.com/thing:2520995/#comments For use with HP Server DPS-800GB Power Supply on the 2020 extrusion. ...

Vertical mount for HP 750w and 1200w common slot power supplies. This does allow for some movement in the mount for easier adjustments. Mounting holes are for 6-32 or M4. I printed these in PETG, 20% infill, 3 walls. ...I would NOT recommend PLA...

See detials on how to do set them up as stand alone PSU's here (read carefully and be safe): http://www.rchelination.com/setting-hp-dps-1200fb-power-supply/ This thing is a mount I designed to attach one PSU to my new Hypercube 300 CoreXY 3D Printer...

These power supplies were utilized in HP and potentially Dell's 1U servers, easily obtainable via Ebay. Numerous companies sell connectors to use them as generic 12V power sources. ...I constructed a preliminary model of the unit using calipers on an...

This is a very simple two-parted plug-on case for a HP common slot server power supply. (The device I made and tested it: DPS-750RB A, HSTNS-PD18) The main purpose is to protect the contacts. There should be enough space for at least eight thick...

Vertical mount for the HP Server DPS Power Supplies

Enclosure for 2x HP server power supplies with Powerpole connectors. No changes were made to the original "plug side". ... @YannikW Many thank's for the time and effort you put into this and for making all your files (especially *.f3z) available!

Cover for HP server power supplies (ProLiant) with cable outlet. It fits tightly and can be held in place with a few drops of super glue. ... Printed with PETG but all other filament types can be used.

Vertical mount for the HP Server DPS Power Supplies Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: Prusament PETG Category: Other