how to update firmware on ender 3 v2 3d models

Needed some feet for my Ender 3-V2 after upgrading the PSU fan and printed this cover for it : https://www.thingiverse.com/thing:4567153 These feet are simple and clean and fits over the rubber feet that are on the printer. There are two versions...

I really liked the design Ender 3 V2 Scraper & Snips Holder from ahuczekdesign but I tend to use a glass scraper more than the paint scraper so I added an extra wide slot for that to fit snugly in to place I then decided that as I us the Needle nose...

Fix for a broken extruderarm on the Ender V2. Did a completely new part, since the measurements for the Ender3 replacements seem to be different. Added extra material in the high stress areas to counter any crack formation. This requires the...

feet for ender 3 35x20 Spool holder: https://www.thingiverse.com/thing:4721912

REMIXED FROM PREVIOUS DESIGNS BY FONSWERKS & MDAVYDIV: 35mm total height, will raise printer by 25mm when installed with rubber feet on Ender 3 models. Suggest printing on flat face. .20mm layer height should be max, designed for .4mm nozzle, no...

This is a DIY enclosure for the Creality Ender 3 V2. Printed parts list: (OPTIONAL) 1x hacksaw_block 16 x 4_mm_plexiglass_fixing 8 x 20x20_three_way_corner All other printed parts that is included in the download but not listed above is so...

I built flat covers for my ender 3 v2. The fronts fit exact size. The back one fits with the motor and if you have only one motor in the back use the front one. it will be the same size. I did mine in silver then painted it. I added a picture of what...

This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once you...

This is AirMachine a Ender 3 V2 fan duct for x2 5015. The Idea behind this duct isn't only to provide lot of cooling but to make working at nozzle easier, you can remove the face and have free access to heatsink, etc. Another point is that once you...

Because I happened to have some chunks of 90x53x300 foam that I was already stacking the printer on. They provided good vibration dampening, but were firm enough to not deform or shake. I added the one top I had to take a chunk out of to clear the...

This is a very simple remix of Kilcrops updates (https://www.thingiverse.com/thing:4764317) to igalopakas design (https://www.thingiverse.com/thing:4614384). The only change is that it is updated to the later revision Clockwork extruder which...

This is a very simple remix of Kilcrops updates (https://www.thingiverse.com/thing:4764317) to igalopakas design (https://www.thingiverse.com/thing:4614384). The only change is that it is updated to the later revision Clockwork extruder which...

It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...

It is possible to get the whole setup on one print if you'd like to do it that way.Tool holder left and right with a left filament wheel or tools designed to fit all original ender tools plus some nozzles.Top main layout for direct drive (Creality...

See picture for wiring to sensor (pin 1 and 2 on the board) (outer pins for the switch) Top filament cutter with a drawer (cutter remixed from Pomi), with a fix to stop the empty line for Cura. Top left holder with 2 sections 1 designed for paper...

I found that the round connector bars on part 2 were too tight to fit into part 1, because they were too close to the objects body. As such you could put them together with some force, but they would not come apart again.. ever.. LOL So I...

Just a holder for Ender 3D printer. ...use a cell phone to monitor your print.

Adapter for installing the hot end of the Creality CR-10 V2 printer on the Creality Ender-3 printer.

Tete Ender 3V2 pour utilisé deux noctua PWM 40X40, s adapte avec le souffleur d origine

Füße für den / Feet for Ender 3v2 und alle anderen / and other 4040 V-Slot Profile

You can choose to print one or two lead screws and Z axis motors depending on how you want it. You can leave the _Dual Z Plate.stl_ out along with the other lead screw and motor if you only want single Z axis. I added a piece of white TPU as the...

This is a redesign from https://www.thingiverse.com/thing:4603075 I've uploades two versions: one with Ender logo and one blank Printed with PETG without Support.

Marlin 2.0.4 Bigtree Tech SKR 1.4 Turbo Firmware.\nI couldn't find a version that matched my hardware for the Ender 3, and I noticed many people were having trouble getting this board running on the Ender 3.\n\nSpecifically, my build enables BLTouch,...

The z-axis bracket (to which the x-axis is bolted on my ender 3 v2) has some y-axis directional wobble. That means (for me) >80mm/s printing, I get some wobble, which means the nozzle scrapes ever so slightly. Because I printed at an angle, the 5020...

Removed the things that slide inside the extrusions and moved and widened the holes to fit M5 screws and T nuts. ...I printed 3 of the non remixed pieces and 1 of this for the front left, so you don't have to disassemble too much stuff.

I made a new Cr Touch mount for my Hero me Gen 7 that's neater for my setupupdate: i upload another mount for anyone who needs if using ABL sensor LJ8A3-2-Z/BX

The STL files are modified *heavily* to increase printability on resin printers. I have not attempted the print on a FDM Printer. Most of the printer is there. I can not speak to the accuracy of the model.The image showing dimensions is for the STL...

The STL files are modified *heavily* to increase printability on resin printers. I have not attempted the print on a FDM Printer. Most of the printer is there. I can not speak to the accuracy of the model.The image showing dimensions is for the STL...

Recomended print with Layers: 3 Infil: 20% Filament: ABS or PETG No need supports

Direct Drive Extruder mount for Eryone ER20 Print Settings: 4 to 5 Walls 4 Top 4 Bottom 20 % infill Extra part needed will be longer stepper motor cable like this...