how to print nylon on ender 3 3d models

just slice and print away

The original duct was lower than my nozzle, so I shortened it. ...There are 2 versions, the "flat" one and the 2mm one. The flat one, once installed will be tilted to point down towards the print, the other will be perpendicular to the nozzle.

The print head is supported by a fixed attachment that holds three LED strips at a precise 30-degree angle, ensuring optimal visibility in low-light conditions.

A small tool to keep the heating bed clean. ... I use a piece of a silicone nozzle sock in the recess, to wipe it off

Small Spring Guide to stiffen the bed and reduce vibration while travelling. ... <h1>Bill of Material</h1> <h2>Basic Parts</h2> 4 x Spring Guide

Marlin needs to eliminate the minimum software limit. The first line of G-code should be set to G92 X0 Y0 Z0. ...Check out this video for more information: https://youtu.be/BKrNZW-KX4I or this one: https://youtu.be/HbLzJ-DYKOc

The Original was a good design, buy the slice was divided in too much pieces, so I decided to make a remix Check the original one in https://www.thingiverse.com/thing:3416367

chimuelo,how to train your dragon ,cookies,cookie,cookies,How to Train Your Dragon

Creality Ender 3 Pro Cr10 Tevo X & Z MGN 12 H Linear Rail One Piece Adapter Easy to Print No Mods Required Just needed 3 x 8mm, 3 x 10mm, 5 x 50mm bolts and nuts and 3 x 300 MGN12H linear rails

To truly understand the magic of "How to Train Your Dragon," one must first grasp the art of baking perfect cookies. It's all about precision and patience, just like training a dragon. ...Now, if you'll excuse me, I need to attend to my cookie-baking...

How to fix animation error in solidworks/ How to crack exploded view problems/ foldable chairhttps://youtu.be/dCV_II03TzM This design was very innovative, we are using to a normal chair (sofa) and tining table space utilizing house interior design,...

The total print time and print orientation are shown in the image (approx 3 hours). No rafts or support needed. Make sure to measure the thickness of the plate to be 2.5mm where it slides into. It will be a bit tight fit at first but once you...

You can see more detailed post-print assembly process descriptions by visiting the forums section dedicated to the Therpf discussion forum for detailed breakdowns from my first-hand experience on Carnifex assemblies created with PLA/ABS printing...

This is the remixed version of the cablechain to be used on an Ender 3 (Pro), when using - Printermods MDD v1.3 adapter plate - OEM/creality extuder in direct drive setup - HMG5 with 2 5020 fans, OEM hotend I installed this cablechain adapter -...

You can use the link below to review the appropriate video cards and drivers for SOLIDWORKS.Link: https://www.solidworks.com/support/hardware-certification/* Another way to turn this feature on is to make a few changes to the registry. However, since...

This is undoubtedly one of the most efficient and quickest-to-print phone stands available on Thingiverse. ...Printing it requires approximately 45 minutes, assuming a layer thickness of 0.2 mm and a print speed of 60 mm/s.

view problems/ foldable chairhttps://youtu.be/dCV_II03TzM This design was very innovative, we are using to a normal chair (sofa) and tining table space utilizing house interior design, My channel is more useful for the Design Engineers - beginners,...

I've created an easy-to-follow guide on how to add an OctoPi shortcut to your desktop. This way, you can access OctoPi with a simple click of your mouse. Follow these steps to set up the icon and enjoy seamless navigation between your desktop and...

I was interested in printing the Dummy 13 but found that without the runners found on the Easy/Mini I had a hard time getting the parts to stick. I realize that the parts are “Beta” and @soozafone plans to make runners eventually but I thought these...

Load the AMF file into Slic3r and then assign your extruder(s) to each layer. ...The example above was printed on an MH3000R1 with 5 extruders from ORD Solutions.

... be sure to reverse the fans by rotating 180 degrees for optimal direction. Replace original washers with shorter ones for proper mounting clearance. Print two shells with 100% infill and full support, remembering to remove supports post-printing.

I designed a custom tool holder to mount my spatula and pliers on the backside of my Ender 3's PSU, utilizing two M4 screw holes that I found no pre-made part for on Thingiverse. The design may prove useful for others with similar needs. Please note...

I have just split the large parts from the enclosure in the middle to be printable on the MINI. There are simple stick connections between the halves. I thought I would glue the parts together, but they hold well just so. ...Printed on Devil Design...

These are a portion of the files from https://blog.prusaprinters.org/mmu2s-printer-enclosure/ that have re-arranged/modified for printing on a Prusa Mini It doesn't include these parts because I assume you are enclosing a mini and don't need them: ...

You can also try pushing the magnets into the holes on the board with your fingernail to decrease their strength and then applying glue before placing the pieces on top. One thing to note is that the holes in the chess pieces are slightly too large,...

The 3mf file should work if you want to change details, but I have not printed using it.Recommended settings:Supports: I would recommend using paint on supports for the base of the deck and for the joysticks. ...paint on supports for the rear triggers...

Hi all, I have made my own version of the Commodore 64 Cartridge case, that is easy to print on an FDM regular 3D Printer. You can print this one face down no support needed. I have a regular version and one with a hole for a small switch. I...

Create glasses on a stick using 3D printing, perfect for the Mini Maker Faire 2017 Portland event.

For example: https://cults3d.com/en/3d-model/tool/creality-ender-3-s1-pro-cr-touch-no-y-offset https://www.printables.com/model/257460-ender-3-s1-zero-offset-cr-touch-mount This fan duct is a must if you are planning on using klipper with the...

My filament on my ender 5 pro kept getting stuck on the holder arm, so I created this piece to fit on the filament holder and keep the filament roll away from the arm coming from the 3d printer.